ozweaver (not verified)

Kristin,

I did not size the warp, and while I have heard of this, I do not have a recipe for it.  Thanks for the idea!... I will investigate.

So far, I have been spraying the warp with a water mister, and today I turned off my de-humidifier and tried spraying the air above the warp!  After weaving for just a few minutes with these conditions, I broke three more warp threads!  I use a temple to weave so these threads did break due to pull in, rather due to abrasion.

Based on Joanne's suggestion about a smaller shed I am attempting to create a smaller shed!

I do love the look of tow linen and hope I make a success of these placemats!  Also, they are a gift so I hope I won't have to abandon the project!

Brenda

www.argoknot.blogspot.com

www.archiebrennanproject.com

ozweaver (not verified)

Kerstin,

Oops!  Very sorry I spelled your name incorrectly in my previous message.

Brenda

www.argoknot.blogspot.com

www.archiebrennanproject.com

ozweaver (not verified)

Joanne,

Thank you for taking the time to consider my situation.  If I may, I will try to state as much info about this project as possible.

Warp: 6/1 tow linen, black (perhaps the depth of color has weakened this yarn?)

Sett: 24 epi, sleyed 2 per dent in a 12-dent reed

Loom: Toika

Weave structure:  Monk's Belt

Weft:  Pattern weft is 8/1 tow doubled, tabby is single wet spun black linen (no label for determining size).

I am using a temple while weaving.

There is a line of 'fuzzies' between the beater and the shaft 1 heddles.  This fuzz has started to constrict the warp threads' ability to raise and lower independently.  The warp threads are catching on each other and binding. Some threads are now breaking.

Thanks for your help so far....I plan to adjust the treadles down a bit , hoping that will lessen the shed.

Brenda

www.argoknot.blogspot.com

www.archiebrennanproject.com

ozweaver (not verified)

Earlier this evening I ran to the store for flax seed in order to make the recipe from Kati Meek's book per Kerstin's recommendation. I have now woven about 4", also implementing Joanne's advice about only beating once and advancing the warp often.  Things look good!

Thank you all!

Brenda

www.argoknot.blogspot.com

www.archiebrennanproject.com

 

claudia (not verified)

Cathy,

When you sampled did the same thing happen?  You might want to check you ppi (picks per inch).  If they are more than your epi (ends/inch) then that could explain why you are getting a more weft faced structure when you weave.  Another way to express it is, if your warp is sett at 10/inch and you are beating your weft in very hard and it comes out as 15-18 ppi then you will be covering most of your warp with the weft.

Do you have any pictures to share?  Are you using the same weight yarns in both warp and weft?  If the weft is heavier then it will cover more of the warp.  If you weft is thinner or finer than your warp then your warp will have dominance.

Just a few thoughts. 
Claudia

lkautio (not verified)

It is more of a question of sett, beat, yarn size, and structure.  It sounds like you have a lot more weft showing than warp (which will emphasize the weft stripes and de-emphasize the warp stripes. I see you are using a rigid heddle loom, so I am going to assume plain weave and a fixed sett. 

Solution 1) Don't beat as hard.  Try for as many picks per inch as ends per inch or fewer. This may not make a good cloth without changing the sett (on a shaft loom) or weft yarn.

Solution 2) Change the weft yarn to something finer that still gives decent cloth.  It might mean going to a different fiber to help the fabric hold together (a wool weft will full or felt a little to a lot in the finishing and help an otherwise sleazy cloth be good). 

Solution 3) If the problem is that the weft is beaten at the same ppi as epi and about the same size as the warp, but you have a fuzzy weft that is obscuring a smoother warp, try a smoother weft.

Solution 4) On a new project change the warp yarn to something heavier and weave with fewer picks per inch and/or a finer weft.

If you were on a shaft loom you could also:

Solution 5) Change the sett so that there are more warp threads per inch.  On a rigid heddle you might pair some or all of the threads through the slots and holes.

Solution 6) Change the structure to one which has more warp threads on the surface (for example a 2/1 or 3/1 twill).  If you have two rigid heddles you can try rethreading with the two heddles (or adding a heddle bar) to get a 2/1 twill.

Have fun!

Laurie Autio

 

wilowind (not verified)

char

 

Thanks for the info. I think the epi is too wide. I'm using the 7.5 dent heddle with sock weight yarn. Perhaps I should have used the 10 or 12 dent heddle.  However the project is turning out all right. I'll finish the scarf & remember to use a heddle to match the weight of yarn.

Cathy S/Willowwind

claudia (not verified)

Hi Cathy,

Sock yarn is a bit thin for 7.5 as you mentioned.  I suggest you consider starting with a sample.  It's a good habit to get into as a new weaver and you can never go wrong.  I have learned to love samples and use it as an opportunity to see how different weft colors and weights work with my warp.  Be sure to add 10-12" extra to you warp length to allow for about an 8" sample and tying back on after completing and removing the sample.  It's important to finish the sample in the same manner you plan to finish the fabric.  That way you can measure for shrinkage and draw-in.

There are untold numbers of good examples why sampling is important.  If you have warp left at the end of the scarf you are making now, you might try different weft materials for future reference. 

Happy weaving,
Claudia

feltedbag (not verified)

I weave a lot with Lisa Souza's Sock! Merino and I use a sett of 12 for a twill.  The biggest challenge in using sock yarn (for me) is that it stretches a lot under tension even when there is no nylon in the yarn. Here's a sample.