How do you get vertical stripes to show? I warped a scarf with vertical stripes, bus, as I weave (with the same colors as the stripes) I get horizontal stripes. Ther vertical ones do not show. What am I doing wrong? Should I use one color weft all the way through ro what? Please help.

Cathy S/Willowwind

Comments

claudia (not verified)

Cathy,

When you sampled did the same thing happen?  You might want to check you ppi (picks per inch).  If they are more than your epi (ends/inch) then that could explain why you are getting a more weft faced structure when you weave.  Another way to express it is, if your warp is sett at 10/inch and you are beating your weft in very hard and it comes out as 15-18 ppi then you will be covering most of your warp with the weft.

Do you have any pictures to share?  Are you using the same weight yarns in both warp and weft?  If the weft is heavier then it will cover more of the warp.  If you weft is thinner or finer than your warp then your warp will have dominance.

Just a few thoughts. 
Claudia

lkautio (not verified)

It is more of a question of sett, beat, yarn size, and structure.  It sounds like you have a lot more weft showing than warp (which will emphasize the weft stripes and de-emphasize the warp stripes. I see you are using a rigid heddle loom, so I am going to assume plain weave and a fixed sett. 

Solution 1) Don't beat as hard.  Try for as many picks per inch as ends per inch or fewer. This may not make a good cloth without changing the sett (on a shaft loom) or weft yarn.

Solution 2) Change the weft yarn to something finer that still gives decent cloth.  It might mean going to a different fiber to help the fabric hold together (a wool weft will full or felt a little to a lot in the finishing and help an otherwise sleazy cloth be good). 

Solution 3) If the problem is that the weft is beaten at the same ppi as epi and about the same size as the warp, but you have a fuzzy weft that is obscuring a smoother warp, try a smoother weft.

Solution 4) On a new project change the warp yarn to something heavier and weave with fewer picks per inch and/or a finer weft.

If you were on a shaft loom you could also:

Solution 5) Change the sett so that there are more warp threads per inch.  On a rigid heddle you might pair some or all of the threads through the slots and holes.

Solution 6) Change the structure to one which has more warp threads on the surface (for example a 2/1 or 3/1 twill).  If you have two rigid heddles you can try rethreading with the two heddles (or adding a heddle bar) to get a 2/1 twill.

Have fun!

Laurie Autio

 

wilowind (not verified)

char

 

Thanks for the info. I think the epi is too wide. I'm using the 7.5 dent heddle with sock weight yarn. Perhaps I should have used the 10 or 12 dent heddle.  However the project is turning out all right. I'll finish the scarf & remember to use a heddle to match the weight of yarn.

Cathy S/Willowwind

claudia (not verified)

Hi Cathy,

Sock yarn is a bit thin for 7.5 as you mentioned.  I suggest you consider starting with a sample.  It's a good habit to get into as a new weaver and you can never go wrong.  I have learned to love samples and use it as an opportunity to see how different weft colors and weights work with my warp.  Be sure to add 10-12" extra to you warp length to allow for about an 8" sample and tying back on after completing and removing the sample.  It's important to finish the sample in the same manner you plan to finish the fabric.  That way you can measure for shrinkage and draw-in.

There are untold numbers of good examples why sampling is important.  If you have warp left at the end of the scarf you are making now, you might try different weft materials for future reference. 

Happy weaving,
Claudia

feltedbag (not verified)

I weave a lot with Lisa Souza's Sock! Merino and I use a sett of 12 for a twill.  The biggest challenge in using sock yarn (for me) is that it stretches a lot under tension even when there is no nylon in the yarn. Here's a sample. 

 

wilowind (not verified)

 

 

I guess I should have made a sample to begin with. The yarn I used was fairly expensive & I didn't want to waste any on a sample. Now I know better. I'll post a photo when I finish the scarf.

 

Cathy S/Willowwind

wilowind (not verified)

 

 

The weft & warp are the same yarn. I think I just used too wide of a heddle. Today I bought a second 12 dent rigid heddle, so I hope to try a small sample with the 10 or 12 dent heddle once I finish this scarf. Its turning out pretty anyway. I'm using sherbert color (oranges, pink, blue/green varigated & a soft yellow.) I'll put it up on the blog once I finish it.

Cathy s/Willowwind

 

 

claudia (not verified)

Holly,

That is lovely!.  Is it a shawl or a blanket?  Did you post it in your projects?  I'd love to see the details on sett and size.

Thanks for the photo.  I have the same problem using sock yarn and I find that on the rigid heddle loom it's difficult to get a good "beat" or place the weft to get an equal epi and ppi for plain weave.  I have used it with other washable wools and that sometimes helps.  Also, I double the selvege on all my scarves and shawls. l find it makes for a nice clean edge.

Your braided fringe is really nice.  What a lot of work and a beautiful result.

Claudia

wilowind (not verified)

 

 

Here's a photo (I hope-last one didn't turn out) of the finished scarf.Striped Alpaca Scarf.I'm still learning how to upload stuff here. The piece is alpaca, at 7.5 epi, is 8' x 64" with no fringe.

Cathy

 
 

Caroline (not verified)

Love the colours! Its very pretty even if its not a plaid, so it might be worth while doing another one now that you have had a few ideas to think about. Scarves need to be soft and floppy if they are to drape properly and its not too obvious from the photos that its sleazy. Did the finishing draw the warp and weft closer together? You would not want it to finish as stiff as a board!

geeksdoitbetter (not verified)

"Also, I double the selvege on all my scarves and shawls."

~ponders~

does that mean you put twice as many warp threads through the heddle on each edge of the project?

 

claudia (not verified)

Yes, that's what I do.  When I calculate the total number of threads I need for a project, I add two more and put one extra in the same hole or slot with the edge thread.  I find it gives a nice smooth, firm edge on both shawls and scarves.  Sometimes I add 4 extra threads and put an extra in the last 2 edge threads.

You can always try it when you sample and if you don't like it, pull it out.  Hope that helps.

Claudia

Submitted by Anonymous (not verified) on