claudia (not verified)

 Sure, all the time.  There are two holes for the second heddle, check either in front or behind the current heddle block.  There is a large hole for the bolt with the wing nut and a smaller hole just below that for the peg which is a tight fit at first.  Take a photo of the inside of your loom on the side bars and we can check if your holes are in the right place.  (it's so hard to write all this with a straight face  : )

Claudia

Manicgirl (not verified)

 Haha, sorry to make this so complicated to describe :D

 

Anyway, I took out my loom and the second heddle posts, and think I might have found the right place:

The new post is towards the back-beam, and I have to find a screw since there wasn't one included when I bought the extra heddle posts. But at least it looks right now, I hope it is too!

 

Thanks Claudia!

Tina

claudia (not verified)

 Tina,

Looks good, I think you got it.  Just be certain the little peg fits in the right spot.  When you add the bolt and wing nut, the peg will hold the heddle block in place nicely.

Happy weaving,
Claudia

PS-What are you going to make now that you have 2 heddles?

Manicgirl (not verified)

Great Claudia, thanks!

I don't know what I will weave, probably start with something with a finer yarn and therefore 2 heddles. But first I have to weave some more log cabin! :)

 

Tina

sewdoggie (not verified)

What is comparable to using two heddles, is it similar to a 4 harness? Probably a stupid question, but I had a 2 harness floor loom and it operates the same as my Kromski Harp, so I'm wondering what 2 heddles compares to.

Claudia Segal (not verified)

I find two heddles useful when doing a 3 shaft weave structure such as a 3/1 twill.  You can also use string heddles to create more shafts and pick up sticks work well, too.

You might enjoy the class Liz Gipson is giving on Saturday, 4/16 on using a pick up stick with a rigid heddle loom.  It's a great way to create various patterns in warp and weft.

Claudia

lkautio (not verified)

Hi Ellen, this is a beautiful piece, but looks very frustrating to weave. I'm guessing you don't normally weave this wide? Here's a couple of things to try. 

Check your treadle cords.  You may be able to change the length to get a bigger shed.  A half inch may be all you need.

Advance more often, perhaps after every inch. That will give you a bigger shed. 

If you have lease sticks in between the heddles and the back beam, remove them. 

Same for a raddle on the back beam or a string across the warp anywhere. 

Push the beater back, throw harder than normal, and throw right along the reed. 

Try to throw straight, the shuttle seems to want to curve toward the cloth.

Don't overfill your quill, it's causing drag. 

Using a bobbin rather than a quill may allow you to fill the bobbin more (cylinder rather than a tapering bulge).

Switch to a shuttle with a longer bobbin. 

Switch to a lower profile shuttle.

There are some rag shuttles that will hold a tremendous amount of yarn and have a low profile.  Not a ski shuttle, they are probably too tall.  It is slower to have to unwind the next shot, but the weaving may be faster.

Good luck!

Laurie Autio

ellenspn (not verified)

 

Gee, I thought I would have been notified of the followup posts.  I guess not!

I had messed with the tie up quite a bit adjusting the treadle cords and the lamms.   I just could not get much else to move.

In hindsight, I should have re-done the repair heddle, as that is where it was catching the most.

The other shuttles I had are much taller (Schacht) than the Andersson shuttles I was using. And I just had borrowed the end feed shuttle and the winding job on the pirn was atrocious! 

If i had to do it over again, I would do a lot of things differently with the tie up before proceeding.

Luckily the end product was worth it.

claudia (not verified)

It does look really nice.

As for notifications, we are working on it.  The developers are able to see the notifications and they are queueing on the website, not going out and we haven't been able to determine why yet.  New comments are appearing in the Dashboard and the tracker view for Groups & Projects.  Both views allow you to click on the red new and go directly to the new comment.

Please add this to your projects, the date field issues are fixed. It looks great and you learned a lot.  

Claudia

PattyAnne (not verified)

I wove that shawl as one of my first projects and LOVED it.  I didn't do anything special with the selvages but rather followed the instructions as Joanne said.

Happy Weaving!

~PattyAnne~