I love my 10 shaft countermarche loom, but have one problem: When I pull out the pegs to start weaving, the shafts have a tendency to drop down in stead of remaining in balance, especially if I have a broad warp and/or use many shafts. Does anyone have advice?

Comments

Sara von Tresckow

 The best place to start is to place your locking pins in position and carefully examine all the connections, not just the ties to the treadles.

The lams should hang straight or point slightly upward. The shafts should all hang at the same height. The cord for the last shaft should be taut to the treadle with the others becoming progressively looser toward the front shaft.

Naturally this is easier to do with 4 shafts than more. If you can't get relief by simply adjusting, try taking the loom back to just 4 shafts for a simple project and getting that much in good adjustment. Observe carefully which adjustments make a difference and how they make a difference. When you hang your other shafts back in, it will be easier to adjust them to fit.

A little drop is hard to avoid - and remember, a tight, even shed floor is paramount in all of this. If you have what looks a bit sloppy with an excellent shed - let it go. We visited handweavers in Germany in the Spring using ancient countermarche looms with loom cord and snitch knots. At rest, they looked terribly uneven - BUT when they pressed the treadles, they got a really good, even shed.

 

Ellen (not verified)

Thank you Sara. You seem just so knowledgable!

I think my connections look just fine, when I have tied everything up. And I sometimes have to adjust the cords for the treadles slightly to get a perfect shed, but then I have no problems after that. Except that I find the heddles have a tendency to cross and get messy when I let go of all the treadles, and this can cause some irritation. Apart from that it is really only this "sloppy"feeling that bothers me.

Su Butler

HI Ellen.....you stated:

"Except that I find the heddles have a tendency to cross and get messy when I let go of all the treadles".....

I think the more likely cause of this is upper lamms that are interfering with the lower heddle bar on the offending shafts.  This causes the lower bar to be pushed up during weaving, and the heddles get sloppy and tend to cross over one another.  It doesn't actually happen when you let go of the treadles, butt that may be when you notice it.  If you can adjust the height of your upper lamms, I think you will see this problem disappear. 

Su :-)

Ellen (not verified)

Hi Su,

Thanks for your reply. I shall certainly check that out. And so sorry for not answering for so long. I have been away for 4 weeks. My situation is that my really good loom is so big, I have not got room for it in my ordinary home, so have to go to my summer residence, a cottage by the sea, to do some serious ´weaving, and that is what I have just come back from. But I have no internet out there. Next time I go over there wil be around Christmas, and will try your advice out then. At home I only have a small loom.

Little Meadows (not verified)

Lately I was having trouble with my first 3- 4 shafts dropping after removing the pins ...the issue was the lower lamms.  Firstly mine aren't long enough and so I may need to weight them a bit but mostly it was my tie up. Never a problem with 4 shafts but going to 8 I need to watch the tie up better.   By making sure that the left most (farthest from the lamm pivot point) treadles were tied to most the lower lamms my problem was solved.  The help for seeing this came from Joanne Hall at Glimakra USA and her mongraph -Tying Up the Countermarche Loom.  She helped me over the phone too - what a patient and helpful person.  If you have a countermarche loom and run into difficulties I would suggest you order the monograph from her.  The Big Book is nice but Joanne has some trouble shooting ideas and a different way of presenting this material that has been more helpful for me.

Liese

Ellen (not verified)

Hi,

Thanks for your reply, but I am not sure I understand how you solved the problem. I mean, the treadles are tied to both upper and lower lamms, and which depends on the tie up pattern, right? So what was it you could do differently, exactly? Sorry for being stupid :-)

And phoning the Glimakra USA is not such a workable idea for me, as I live in Denmark :-)

I think I have the same problem as you, though. According to the text books the lower lamms ought to be slightly longer then the upper ones, but mine aren't, either. Which sometimes causes rhe tie up strings to slip around to the wrong side of the lower lamms when I weave. This is just a minor nuisance once you have discovered that tendency, just check it regularly, if something feels slightly wrong when treading.

Little Meadows (not verified)

Hi Ellen,

Yeah calling internationally is probably not an option but you could email.  According to Joanne you want the farthest most treadle to have as many if not all the lower lamms tied to it...that way the weight of the treadle way out there at the end of the fulcrum can help hold down those lower lamms so the shafts don't sink. What I did was change my tie up so that the 2 outmost treadles (outmost from the lamm attachment, which for my loom is on the right, so I'm talking about the left treadles) were attached to all the lowers between them.  Now say for instance that you have 10 treadles and only need to use 8-9, take that outmost treadle and just attach your lowers to that treadle and use the rest for your tie up; this 10th treadle is a "dummy" not used in the treadling but helps balance your shafts.  Also she says that Glimakra now makes the lower lamm length almost as long as your loom is wide. So my longest lower lamms are almost 10 inches too short!  And since I got 3 different lamm lengths when I bought this old girl some of my lowers are like yours-really too short.  Her suggestion to remedy this until I can order/make new lamms is to weight the lower lamms.  I'm going to try fishing weights held on with rubber bands.

Hope this is clearer,  Liese

Ellen (not verified)

Hi Liese,

Thank you very much. Yes that is very helpful. Hm, might go for trying to get hold of longer lamms sooner or later. In the meantime, I'll try to follow these ideas. Except for the not so frequent cases where I use all 10 treadles for the tie up, I think I get the picture. IF I do use all 10 for a specific pattern, I still can't really see how you can decide to attach especially many treadles to the lower lamms. But maybe it'll come to me when it becomes relevant the next time :-)

Thanks again;

Ellen

Submitted by Anonymous (not verified) on