Welcome to our Rigid Heddlers group second Weave-A-Long!

This WAL consists of 12 different 3S Twills woven on our Rigid Heddle looms set up with two heddles.

So grab your RH looms and two contrasting colors of yarn and lets have some fun.

The following draft has the warp one solid color and the weft a contrasting color.  Ten of the treadling sequences will be done with the weft a contrasting color.  The last two sequences will be done using one shuttle with the 'blue' weft color and a second shuttle with the 'yellow' warp color.  Of course, you are free to use whatever colors and yarn you want.

The first treadling sequence is actually a plain weave.  The second is a traditional 1/2 Twill and the third is a traditional 2/1 Twill.

For our Rigid Heddle looms the heddles are threaded as follows.  Heddle I is represented by the bottom holes and Heddle II is reprsented by the top holes.  Warp Thread 3 is threaded through the slots of both heddles.  Warp Thread 2 is threaded through the slot of Heddle I and a hole of Heddle II.  Warp Thread 1 is threaded through the hole of Heddle I and  a slot of Heddle II.

In a few days I will post more treadling sequences but please work at your own pace and feel free to ask lots of questions.

Now let the fun begin!!!!!!!!!!!!!!!

Susan

Comments

mmorse (not verified)

Hello, Doreen,

That's clear. I'm still not getting 6 and 7, and by your description, the long floats on the back and general padded appearance may be the result of using what in other circumstances seems to work as shaft 3 (both down). I'll do some more testing. To add some additional challenge, I re-warped with my own handspun (spinning my way through a fleece toward a large project and I wanted to see how it would look), which sticks together a bit. The twill is more uniform with tamer wool (I need more practice spinning).

--mm

CraftinSusan

Here are the last two drafts for our WAL. 

 

These are the same as the above two but these are done using two shuttles with one shuttle with your warp yarn and the other shuttle having a contrasting color.

I apologize but I haven't had a chance to check out drafts 6 & 7 and compare them to the drafts in my 3S book I am using.  For those of you having problems with drafts 6 & 7 please just skip them.

kellytwo (not verified)

Thanks Susan, I still have to do sample 10 before I start these last two. I really like sample 9, it's my favorite so far. I haven't looked at the under side yet, but the draft makes it look like both sides will be the same, which is the type of pattern I was looking for. If I use it for a scarf, I want both sides to be the same.

If you look at the sample 6 draft, the shaft 2 thread never gets picked up, so it just floats along under the bottom. The same with the draft for sample 7, the shaft 1 thread never gets touched.

Doreen

 

 

 

 

 

CraftinSusan

I am glad that you are having fun with the drafts.  I hope that you will post some pics!

I did notice about the threads that didn't get picked up on samples 6 and 7 but I haven't had a chance to check it against my reference book to see if I made a mistake when I inputed it into PixeLoom.

claudia (not verified)

Hi Susan,

I just dropped in while on vacation, to say you are doing a great job and, although I cannot join this WAL, I am using your drafts to weave along on my new to me Glimakra while I get used to the countermarche system of weaving.  You have inspired me to return to some of the basics of weaving with 3 and 4 shafts.

I do have my Harp with me now and have been working on a quick tencel scarf I want to finish before our next show on 6/5.  I needed something quick so opted to let color do the work and am doing plain weave with a hand dyed Just Our Yarn 5/2 tencel weft and a plain yellow/gold warp.   It's fun watching the weft colors develop as I weave.  I will post the project when we get home tomorrow.

Thanks for your hard work and the inspiration you have provided beyond our WAL.

Claudia

CraftinSusan

Thanks, Claudia, for the kind words!  I hope that you are enjoying your vacation.

I tried to post this last night.  We had a very short but severe thunderstorm pass through.  Lightening strike took out a substation near us.  Our entire area was without power for almost 4 hours.  Because of the heavy rain we had water in the basement very quickly do to no power to the sump pump.  My husband started our emergency generator only to have gasoline leaking out the bottom.  Right after that the electricity came on for about five minutes just long enough for the sump pump to empty the drain.  When the electricity finally came on and stayed on we quickly wet-vac the rest of the water.  We do know that our basement will flood if the sump pump is off so there was no damage.  Everything stored down there is in water proof bins or off the floor.  What a night!  Last week I had actually gotten rid of a lot of stuff in the basement and reorganized some of it so cleaning up the water went quickly.

claudia (not verified)

How goes the WAL?  Does anyone have pictues to share?  Has anyone finished all the patterns Susan provided? 

Claudia

CraftinSusan

Susan hasn't finished all the patterns Susan provided!  LOL  I have been taking pictures as I have been weaving and will post when I get done hopefully in a day or two or three.

I haven't forgotten about drafts 6 and 7 either.  For those working through the WAL just skip them for now.  These are the first two drafts in Post 36.

Susan

kellytwo (not verified)

I still have 3 more samples to weave. I'll take pictures as soon as it's off the loom.

Doreen

Jean9 (not verified)

Hi

Very late joining this WAL but have enjoyed reading the posts. I will be doing the patterns as soon as my loom is free. I was just wondering if all the treading possibilties are posted somewhere?

IE:

shed 1 - Heddle 1 up, heddle 2 neutral.

Shed 1 and 3 Heddle 1 up, Heddle 2 down. (no idea if that is correct just using it as an example).

I have used 2 heddles for double dpi weaving but have yet to try any patterns.

CraftinSusan

Welcome to the WAL!

If you look at my handdrawn picture on warping the two heddles, you will see the Warp Thread 1 is through the hole of Heddle I and slot of Heddle II.  Warp Thread 2 is through the slot of Heddle I and hole of Heddle II.  Warp Thread 3 is through the slot of Heddle I and slot of Heddle II.

Depending on what loom you have you may have to modify the following.

Shed 1: lift up Heddle I, Heddle II in neutral position

Shed 2: lift up Heddle II, Heddle I in neutral position

Shed 3: bring both heddles to the front of the heddle block, push both heddles back so they are touching each other and the heddle block and push both heddle down to bring up Warp Thread 3.  Alternatively use a pick up stick to pick up Warp Thread 3 in the back of the loom behind the heddle block.  Leaving Heddle I and II in neutral position turn the pick up stick on its edge to lift up Warp Thread 3.

Shed 1 and 2:  Lift Heddles I and II.

If you are not using a pick up stick;

Shed 1 and 3: push both heddles down to bring up Warp Thread 3 and slowly lift up Heddle 1 until Warp Thread 1 and 3 are at the same level.

Shed 2 and 3: same as above but lift Heddle II.

If you are using a pick up stick

Shed 1 and 3:  Lift Heddle I and turn pick up stick on its edge

Shed 2 and 3: Lift Heddle II and turn pick up stick on its edge

Play around with the different ways until you find the ones that work for you.

Caroline (not verified)

A RH loom has no treadles, but a lifting plan, and this is what you see down the right hand side of the pattern draft. If you look at the top right hand square, it gives you the different combinations of sheds necessary to make the pattern - you have a choice of 2 sheds, and then the rows of squares below that tell you in what sequence you select and manipulate the 2 RHs to get the pattern. 

If you follow the WAL from the beginning, it starts with the threading plan and lifting diagram for a plain twill, then builds up to introduce patterns that get progressively more complicated as your skills build up. The discussions will give you a good idea of bits that weavers have found tricky. The sheds used are talked about and explained, otherwise you can PM CraftinSusan if there is something you do not understand, or is taken for granted and not mentioned.

Good luck with it - its kept everyone very busy!

betzfrederick (not verified)

I have been planning on doing this WAL for a couple of months but life kept getting in the way. Now I am ready to start!!  I am wondering if I should  use two 10 dent heddles with 3/2 ASTRA on my Beka loom.  Does anyone have any advice?  Has anyone tried the WAL with 3/2 ASTRA?  Thanks, Betz

CraftinSusan

Welcome to the WAL!

I googled and 3/2 cotton is around 20 WPI.  So with one heddle we would use a 10 dent heddle to get a balanced weave.  But with 3S Twill using two heddles on a RH loom we will get a density of 150%.  If we use two 10 dent heddles, 10 x 1.5 or 15.  That means we won't get a balanced weave.

If we use two 8 dent heddles, 8 x 1.5 = 12.  This number is closer to 10 but we may or may not get a balanced weave.

If we use two 5 dent heddles, 5 x 1.5 = 7.5 rounded to 8.  Again we may or may not get a balanced weave.

Since 3/2 Astra is between, you could try either two 8 dent heddles or two 5 dent heddles.

If we skip holes and or slots in the front heddle we could reduce the density to around 100%.  If this is your first foray into using two heddles on a RH loom than I am not sure I recommend going this route.  But if you only have the two 10 dent heddles and are committed to this yarn I can help you come up with a hole/slot warping pattern.

betzfrederick (not verified)

Thanks for your explanation. I didn't look up the wpi.  I used a common yarn sett chart and found the sett for 3/2 cotton is 10-14 epi for tabby and 15-18 epi for twill.  That is why I was thinking two ten dent heddles would work since 150% of the epi would be 15.    I do have two 8s I could use though. 

I have another question.  Could you explain when you would use sett and when you would use wpi?  Are their specific instances when you should use one rather than the other?  I appreciate your help.  Betz

CraftinSusan

The chart I saw only had 3/2 Astra listed at 19 WPI.  So to get Ends per Inch we divide that by 2 to get 10 EPI (rounded).  To get 14 EPI that means WPI is 28.  It is possible that another brand of 3/2 cotton is thinner than Astra.

I am not sure I can totaly explain the terms but they are all related to each other and the final density of the fabric.  And the final density will also depend on how tight the weaver beats in the weft.

WPI= wraps per inch.  We take a ruler and wrap the yarn around it for two inches and then divide that number by 2.  Using two inches gives up a more precise count.

From WPI we determine Ends Per Inch.  EPI=WPI/2.  Using 3/2 Astra at 10 EPI, this means that for a balanced weave tabby we will have 10 warp threads per inch and 10 weft threads per inch.  If I was using a multi-shaft weaving loom with seperate heddles and reed I could thread a 10 dent reed with one thread per dent.  If I used a 12 dent reed I would skip two dents over that inch so my Sett would still be 10 threads per inch in the reed.  If I threaded all 12 dents I would get a denser weave.  For twill using a 10 dent reed, I would have two threads in one dent, one thread in the next dent, etc to get 15 EPI.

RH looms have the reed and heddles merged into one so that changes our way of warping the loom and what rigid heddles size we use.  Patterns also change the density of the woven fabric.

Tabby: 10 EPI.  Twill 15 EPI.  The difference between the two is 1.5 which is why we use that number to determine the rigid heddle size when using two heddles.

I used a fingerweight yarn for my twill sampler.  Normally I would use for tabby one 12 dent reed.  So for twill I used two 8 dent reeds.  The sampler came out having a nice drape (density).  I warped for 6 inches and the woven fabric was 5 inches.  Normally I would expect for tabby to have a draw in of half of an inch or less over 10 inches.  With twill which has a sett of 15 I got more draw in which is what we would expect because of that sett number.  For my sampler it didn't matter how much draw in I had.  However, if I needed a specific width I would have to allow for that draw in by having a wider warp.

I am sure others here on Weavolution could explain all the terms better.

betzfrederick (not verified)

Thanks.  I am going to use two 8 dent heddles as you suggested.  I was planning on making the warp 3ft long and 6 inches wide. Each of the twelve sequences will be five to six inches long so they are square with a pick or two between each sequence.   How does that sound?  How long was your warp?   I appreciate your help.  Betz

CraftinSusan

Before you start you may want to read through the entire posts and you may want to only do ten of the drafts.  Two drafts had problems with floats.  I never did go back to check to see if I did something wrong when I recharted them for this WAL.  I know, my bad!  I believe that I put on a three yard warp six inches wide.  Between drafts I only had four picks of tabby in a different color.  I skipped the 'problem' drafts and wove the other ten drafts.  I had about 24 inches extra of warp left.  I wove that off in a single color 1/2 Twill because I had that color on the shuttle.  I also wove the drafts so I had a square of 5x5 inches for each.

betzfrederick (not verified)

I think it was drafts 6 & 7, correct?  Betz

betzfrederick (not verified)

I'm trying to figure out how to thread the heddles.  Which heddle is the front one?  The one with the red thread in the holes or the one with the blue thread in the holes?  Sorry to be asking so many questions.  Thanks for your help.  Betz

claudia (not verified)

Hi Betz,

The first post in this series of comments has the three threads and two heddles in a drawing.  The red line is a thread, the heddles are the 2 sets of holes and the spaces between the holes represent the slots of the heddles.  Here is the explanation for threading the 2 heddles:

So, the red line is thread 1, the blue line is thread 2 and the black line is thread 3.

Hope that helps,

Claudia 

kellytwo (not verified)

The problem samples were #6 and #7. They had floats along the back that never got connected. They just keep floating along. The front heddle is the one with the red thread in the holes. The picture is drawn like if you were sitting at the loom looking at the heddles.

betzfrederick (not verified)

It does help.  Now I'm ready to warp.  Thanks again.  Betz

Submitted by Anonymous (not verified) on