Due to a nerve injury in the back of my thigh that won't let me treadle a loom from a sitting position (or drive), I was off my big looms for more than a year.  In desperation I decided to lift my 40" Maccomber on heavy medical texts (approx 2.5" high) at each corner.  Having just woven a blanket, I find I can weave about an hour a day standing which is a whole lot better than nothing.  I would like to lift my loom in a more permanent manner.  I was thinking 3x3 studs under the 2 sides and another under the wooden strip under the Treadles.  Does that seem stable/safe?  It did not seem to move at all on while on the textbooks and I am not weaving heavy rugs. I don't want to do something that will risk warping the loom. 

Also, inexplicably the hooks have started spontaneously popping off.  This only happened 3 times in 90" but it's horrible unweaving if I don't immediately notice it (Double wide blankets so I didn't see the pattern change underneath).  

Any thoughts appreciated.  Cheers

up

 

Comments

Queezle

I have lifted one of my looms to allow me to weave in a standing position.  I cannot advise you on the popping hooks, but I can tell you about my experience.

I started down this path when considering the health repercussions of too much sitting, and seeing many of my colleagues installing standing desks.  I converted my 4-harness schacht standard into a standing loom by doing two things.

First, I achieved the lift first using random pieces of wood, but for me, this was not very stable.  I replaced the wood with purchased bed risers (~ 4 1/2 inches, Target, less than $10).  These risers have recessed areas that the loom legs fit into, with some extra space.  The size of recessed areas vary, but these ones fit my loom well.

Second, I had to change the treadles.  I needed them to extend farther out from the breast beam so standing was balanced while weaving.  It purchased inexpensive wood from Home Depot, and used a jig saw and drill to make the appropriate holes and slots, and they are now long enough to extend a foot in front of the loom.  Longer would be even better.  I also partially disassembled the loom to modify the mechanism by which the treadles are attached to the loom.  By raising my loom, the treadles were at a steep angle, making treadling uncomfortable for me.  I lowered the treadle assembly, pulled it in front of the loom, and made new (longer) tie-ups between the treadles and the lamms. 

My modifications are still a bit makeshift, the treadle assembly floats on the floor in front of the loom (and moves around a bit), but it would not be terribly difficult to attach it to the loom to stabilize it.  My treadles are inexpensive pine, and it would look nicer done in matching maple. 

But - I do love stepping up to my loom, and immediately weaving.  I had not thought about the fussiness of getting my bench into a comfortable position before weaving, but the ability to just walk up makes it super easy to just step into my studio and weave.

You can see photos of my loom modification here on Ravelry, but I think you need a (free) membership to enter the site.  I've pretty much given up on posting projects here, awaiting the long-promised site upgrade.  Post here if you want any additional information.

sandra.eberhar…

The hooks may pop off  because the loom is not level. All sorts of odd things happpen when it's not level.   Also, I'm not sure what the difference is between the lamms on my Baby mac and your Mac, but when I tie it up, I use a pair of pliers to pull the hook onto the lamm.  They don't go anywhere.

Michael White

I would use 4 x 4s ,untreated, under the sides which I would screw down. On a 40" loom I do not think you would need to worry about the supports under the treadles. But if you find this to be a problem you could block them up. Do you have the new type of hooks or the older ones for the lamms with holes in them? 

Michael White

I would use 4 x 4s ,untreated, under the sides which I would screw down. On a 40" loom I do not think you would need to worry about the supports under the treadles. But if you find this to be a problem you could block them up. Do you have the new type of hooks or the older ones for the lamms with holes in them? 

fiberassociations

Thanks Michael.  I am very short and since I am comfortable standing with 2.6 inch elevation now I am worried that 4¨would be too high but I could pretend to try it out with a few more books. 

Yes, I have the new hooks and the old lamms. I read you or someone commenting that this combo doesn´t work but it has worked for me for probably 10 years.  I am now guessing that the books are not identical height and so unevenness is part of the problem.  Also, I had been too lazy to close the hooks with a pliers once they are on, but I may try that.  

fiberassociations

Thank you for all the details.  I had just seen those bed risers at my mom´s house but since the Maccomber doesn´t have feet I am not sure they would be better than just studs.  
I may not be as handy with carpentry as you are but I will think about extending the treadles.  Thanks, 

Michael White

a 4x4 is 3.5 inches. A 3x3 is 2.5 inchs. THere are 3 differance sizes of new hooks.

Queezle

I originally only raised my loom by about 2 1/2 inches, and liked it.  But after longer weaving sessions, I had some tension in my shoulders and neck, I think from leaning over.  For me, ideas about height optimizing came from reading discussions of loom bench height.  I decided the critical thing was that my elbows always cleared the breast beam.  When I made my loom higher (dictated by the risers I purchased), it was even more comfortable.  I too am short (5'2"), and the best thing is to figure out what works well for you - to know that modifications are possible -  and to inspire others with disabilities to explore novel approaches to maintain their crafting time.  Good luck!

Submitted by fiberassociations on