I've been weaving rugs with my 63 inch Glimakra stanard loom, not feeling the need to add the remaining four shafts.  I'd like to put them to use now if I can.

I have Joanne's book, Tying Up the Countermarch Loom.  I've just finished a project and have not removed it from the loom.  When Becky A helped me put my first four shafts on we needed a threaded, sleyed, tensioned warp.  Can I hang the other four shafts with this warp, or do I need to do it with my next project?  I'm a little confused.  Thanks.

 

Diane

Comments

Joanne Hall

Hi Diane,

Do you want to re-thread this four shaft warp to all eight shafts?

Joanne

Diane Roeder (not verified)

Hi Joanne,

Not unless I have to; it just seems like a good time to add the other shafts.

 

Diane

Joanne Hall

I think I understand your question.  If the warp is finished, then you can put the other four shafts on now.  But it would be easier to first cut off this warp and beam on a new warp.  There is no need to have the shafts in the way while you do this.  It is just easier to add them right before you need to thread them.

It is like setting the table for a dinner two days in advance.  It is easier to do it later so you won't have to work around all those things being on the table for two days.

You do not need to put them on until you have a warp planned which uses all eight shafts.  If there is a chance that your next warp is a four shaft or a five or six shaft, it is best to wait until you have the warp planned, wound and put on the loom.  And besides, you do not want to make a decision on the lengths of the cords for the extra shafts, lamms and treadles until the heddles for those shafts are threaded.  So, if you put the cords on now, you will have to adjust them or at least check them after your new warp in on.  Then you are doing it twice.  If you put the shafts on right before you thread them, you are only doing the tie-up one time.

Joanne

Diane Roeder (not verified)

Thank you Joanne for your very complete answer; I understand your response.  Guess it's time to sit down and do some planning!

 

Diane

Joanne Hall

Hi Diane,

I do understand the desire to just put them all onto the loom.  Then step back and say 'It looks beautiful'.  I really enjoy working at the loom, even the assembly and warping.  But a logical approach is good, especially if you suddenly decide that another four shaft rug is needed now.

I know that some weavers treat this loom just as they do a jack loom, putting all the shafts on and then just using four.  It can make sense to do that on jack looms.  They often have shafts that are difficult to remove and put back on.  And frequently the heddles are also diffucult to remove.  So, they just push the heddles aside on the extra shafts.   And sometimes when you beat hard, the back of a jack loom will bounce.  So, keeping some extra of those heavy shafts in the  loom can be an advantage.  Jack loom shafts can weigh up to 6 lbs each.  I have a friend who decided to weigh hers.

But the Glimakra loom has shafts that can be removed in about 20 seconds and they are easy to store.  I do leave the countermarch cords on the countermarch and tie them to the side frames.  

It is nice to have the flexibility.  I usually slide the shafts to the back of the loom for threading as it is more comfortable and so easy to do.  It is nice that the shafts are so easy to remove and put back on. I sometimes remove the front four shafts when I am threading an eight shaft weave.  I then thread the back shafts, 5 to 8, leaving the threads for the first four shafts tied in bundles.  Then I put the front shafts back in the loom and thread them.  That prevents errors and makes the threading a lot easier.

Joanne

 

kerstinfroberg

When I went to weaving school we always had to take *everything* (shafts, lamms and treadles) off the loom (all and any looms) when we had completed a project. We were asked to leave the looms completely naked (as in "loom frame only") for the next person/project.
The next person (which could be me) then had to put whatever needed (2 shafts, 3 shafts, 4 shafts... 16 shafts; 2 treadles, 3 treadles... 24 treadles) back on the loom chosen for the specific project.
Now (I've had my old 16 sh CM loom for going on 25 years now) I rarely take anything off, except shafts. The unused treadles can stay where they are, and I have found a way to handle the unused lamms. However, I hang up (and take down) shafts as needed for the project I'm weaving.
And yes, I re-do the tie-up all the time, too.

Submitted by Anonymous (not verified) on