claudia (not verified)

Hi Janet,

Ditto on all you said, and we are the exact same age.  I am glad I learned on a jack loom and even happier to now own the Glimakra Standard.  The video and books are a big help.  I have pictures but left the camera somewhere odd and can't find it just now.  I have the loom warped and am putting all the new texsolv cords on now.  It's quite time consuming but I am glad to be doing it. The old cords were just nasty.  I have just finished all the new ones on the top countermarche part and am moving down to do the lamms and the treadles.  Maybe I'll be weaving by tomorrow.  (I should mention that I am squeezing in all this loom cord replacement in between Weavolution meetings and marketing work which takes about 8 hours/day-my full time volunteer job).

Claudia

claudia (not verified)

How do you check to be certain the beater is square? I also have 5 choices of where to place a wooden pin in the top of the beater, above the cradle.  I assume that is to place the warp in the center of the reed when in the beater.

Claudia

claudia (not verified)

Ok, now it's about the treadles.  I am slowed down by having to look down and see which treadle my foot is on.  They seem pretty close together.  Is there something I'm supposed to have in between each treadle in front?  It doesn't look as though anything would fit but I have to fish a bit and look down to check I'm in the right place.

Any thoughts or suggestions would be greatly appreciated.

Claudia

claudia (not verified)

Thank you everyone for your suggestions.  I like the rubber band idea and will try that today.  I use ballet slippers while treadling, they have a little bit of leather on the bottom that makes it easy to stay on the treadle.  Of course, I could be completely barefoot because so little pressure is required to get a great she and the treadling is lighter than my 4 shaft Baby Wolr.

My body fits this loom much better than the TOTT and I am still stunned at how quickly the tie-up went.  I expected to put everything on and then take a couple days to get it all tensioned correctly.  Not so.  I put it on and sat down and started weaving.  What a great start.  The tie-up kit was worth every penny and the video by Becky Ashenden is a very good introduction to Swedish weaving.  I learned quite a bit.

And, of course, having the all of you on Weavolution to help with my questions and my learning curve made it so much easier.  I don't think I would have embarked on this loom without your help.  Or, if I had, I know I would not have been so successful.  

Thank you, everyone, for all your help.  I'm sure this will be an ongoing conversation.  I am, after all, planning on adding the other 4 shafts in the near future.  That should be interesting.

Claudia

conib (not verified)

What a great smile!  And yes, I agree with Marie, this photo of you absolutely should be your Weavatar image.
:-)

-- Constance

claudia (not verified)

Thanks for the compliments, I just uploaded it.

Claudia

Aunt Janet (not verified)

Cool!  I love the lines of the shaft holding strings on the left.  It is so artful.  Yes, great smile, too! 

I have to admit that the old cords on my loom are also "nasty", as you said.  There is a smell of mildew and maybe mouse pee.  Yuk!  I'm keeping my nose out of the cord basket.  I will eventually replace the nasty cords, but want to weave, NOW! 

I've had a busy week at work in my mill.  How frustrating to have my beautiful loom sitting over there in my studio, which is the same room as my mill, and I must work at carding.  It isn't that I don't enjoy the work, but the loom calls.  It is much easier for me to spin yarn while working, than to weave.  I set my wheel so I can see both ends of the carder, so I'm ready to jump to if anything goes amiss.  It is more difficult to leave the loom, and I can't see the conveyer belt from the loom seat.  I also want to weave with uninteruppted time.  So today I'm giving myself some weaving time.  DH will be gone for the day, which will help.  I'd love to get my rugs off the loom and start a new project.  Pretty funny, I'm loving weaving these rugs, but can't wait till I start the next one.  I might even make my warp for my next project before finishing this one.

Off to weave...

Janet

jander14indoor (not verified)

Old thread, but it has the best discussion to a question that was bothering me.

I'm setting up my new to me/used Cranbrook loom with hanging beater.  I've still fairly new, been weaving on a Baby Wolf with upright beater.  From what I'm reading when I advance the warp, I want to set the fell line slightly forward, say one inch, from where the beater hangs vertical.  Then weave until fell line is maybe 1 inch behind where the beater hangs vertical.  At that point I should move the warp and start over, or move the beater back a notch or two.  Please correct if I have that wrong.

But that brings up my quandary.  On my Baby Wolf, the beater naturally lays back out of the way when the shed is opened and I throw the shuttle.  Obviously this won't happen with the hanging beater.  Is part of the action now to push beater back as I open the shed, throw shuttle, beat?  Or is there some other sequence?  Is this why I've seen pictures of the beater being held back by elastic so the action is more like an upright beater?  Is the elastic a good idea?

Any advice appreciated, thanks,

Jeff Anderson, Livonia, MI

cottageweaver (not verified)

While you are adjusting to your new body motion with the hanging beater, train yourself to grasp the beater right in the center every time, not off to one side or the other (good body mechanics and a level fell line).

jander14indoor (not verified)

Thank you all for your responses, a couple of followups.

 

The loom is a Cranbrook, so yes the beater has multiple positions and is light to swing.  Reedguy, your comment gets back to my first paragraph.  I'm sure after a while weaving I'm going to learn where the beater should be and when to move it by feel as much as anything else.  But to start, throwing that first pick after advancing the warp, where should the reed be with respect to the fell line when the beater/reed is vertical?

 

Sounds like this is going to take practice on the motions.

So, left hand holds beater back, right hand thows, left hand releases beater and catches shuttle, right hand moves to beater to actually beat the pick?  and back with hands reversed.

 

On centering my hand on the beater, is this a case where a tactile reminder (rubber band, piece of sand paper) will be helpful while muscle memory is developing?  Kind of like the bump on home keys on many keyboards?

 

On a different topic.  Since it is important to center the warp, and they always have a specific width, is there a reason there are no reference marks on the loom as shipped?  Center point on the tie-on sticks, reed holder, etc?  Am I just being an Engineer (my profession) when the first thing I do is to mark up the parts that relate to the warp with a center line and then a scale to either side showing width warp?  I also marked the tie on sticks to make sure the ties located properly.

 

Thanks,

Jeff Anderson

Livonia, MI