wannaGTD (not verified)

I tried using yarn I had on hand for my first warp...8/4 carpet warp. I first tried making the heddles out of some tencel I had...thinking it would be smoother/slicker than the carpet warp, but I ended up getting all sorts of yarn fuzz from the warp making it very difficult to change the shed. So then I tried using some 5/2 mercerized cotton for the warp. I started out better but it too started collecting yarn fuzz and making it difficult to change the shed as the heddles then want to start sticking together. So the slickest I had available was some fishing line. Some of the heddles allow me to swotch sheds easily but not all. Needless to say, I'm getting rather frustrated. Open for some suggestions here. Should I just scrap this carpet warp warp and try something different, or what else could I use for the heddles. Not sure really where the bulk of the problem lies, with the warp or with the heddles.

wannaGTD (not verified)

...Good to know this is probably user/technique issue and I'm not the first to struggle with it.  I will re-review the videos you have so graciously provided....They are what got me this far to begin with!  I'll try and break it down what I'm doing wrong to see how I can fix the technique.  Thanks

sarahnopp (not verified)

I have been using a nice cotton carpet warp too and am quite happy with it. It is the Maysville brand. (In fact, I need to go get some more color choices!)

For string heddles, I am using a nylon cording. I believe it was marketed for clothesline? It moves very nicely and does not seem to collect much from the warp- even when I have tried a wool or acrylic. Just make sure to burn off the ends or the cord will fray out quickly.

Claudia Segal (not verified)

I believe the 20" weaving width means that you need to have at least 20" of weaving width to complete the project.  The warp, in the reed, measures 19" and you should have at least 1/2" space on either side, totaling 20".

The use of the temple is based on the width of the warp in the reed.  You indicate that the width in the beater (reed) is 19".  If you use a temple it should measure 19" too.

Can you provide some pictures of the "loops" you mention?  Make sure you are placing the weft in at about a 30 degree angle and it is firmly against the side of the warp.  There will be a slight amount of draw-in as you have seen.  You measurements seem accurate.  

Hope that helps,

Claudia

 

naturalfibres (not verified)

I would usually tie on no more than 1/2" bundles, as I find that this makes my tension better across the warp.

suzyhok (not verified)

I've seen this idea before but have never used it.  I think I've always been worried that it would get in the way of throwing the shuttle...  Next project ... I'm going to give it a try.  I love simple solutions!!!

Thanks for sharing!

:-)  Suzy

sewwhatsports (not verified)

I bought a set of the chip bag clips that had 1-1 1/2" clips (in width).  I added a small pill bottle filled with nuts from the hardware store and wrapped the string around the top part of the clip.  Easy 'temple', can move it quickly, set how much weight is needed to hold the selvege  and no holes in my weaving

lkautio (not verified)

I use Peggy's tie on method which has very little waste.  I tension the threads, tie an overhand knot, then open a plain (or plainish) weave shed to put the tie-cord through.  I leave the shed open during the tensioning process which allows the cord to move freely.  Push down with your hand or a stick on top of a very loose open shed to start to get the bundles roughly even before tightening.  For the poking, just jab each knot with a finger or your thumb working from one side to the other.  Tighten the tension one click on the ratchet (or a small amount on a break without ratchets), then poke again starting at the opposite side.  I use 1/2" to 1" bundles depending on how wide and coarse the warp is.  Use a smooth strong yarn for the cord.  You want it to move easily.  The process is fast and easy most of the time. When done I weave 3 picks without beating, then beat, and repeat until the warp is nicely spread out.

Laurie Autio

trplr95 (not verified)

Another substitute for a temple is to use hemostats.  They clamp shut, with their jaws firmly attached, and I can tie a piece of yarn to the handle end - and because it is firmly clamped the yarn does not slide off.  I can attach the other end of this yarn to something weighty - a pair of scissors, a small water bottle, etc.  Hemostats are available on ebay for just a couple of dollars each. 

Trish