TinaHilton (not verified)

I'm getting caught up on my forum posts here.  My husband built a warping trapeze for me to use with my LeClerc Mira.  That loom is gone and I need a wider board/rod for my AVL since it's a wider loom.  But even with that, I can't quite figure out how to set the legs against the loom.  I'm thinking more and more about trying to hook it to the ceiling like yours Laura.

I mostly warp sectionally on this loom, but plan to do some warp painting this summer so I'd like to use the valet for that.  And I want to take the time to try using a reed in place of the raddle.

Thanks so much for all the photos.  It's much clearer than just words, so I appreciate you taking the time to share them.

TinaHilton (not verified)

My warping valet was made using the design in Kati Meek's book.  I'll have to try figuring out where to place the legs of the valet.  But first I still need a longer piece of wood for on top.  It was sized for the 45" Mira.
 
Laura - is the "very tight choke tie" added by you before beaming?  I assume so, since I haven't seen a tight choke tie on a painted warp because that would prevent dye from going through.  I've always been nervous about removing the tie on the end loops and "losing" the end spot and affecting the color placement.  That's the main thing that makes me nervous about rough sleying through a reed with a painted warp.

TinaHilton (not verified)

I didn't think about that being part of the loom waste Laura.  I've only done two painted warps.  The next one will be better with these tips.

villageweaver (not verified)

I just replaced the top horizontal for the same reason. I went to home depot and bought a 7 foot long oak board. Mine was 3/4 inch because that's the size in the verticals that hold it. Then i took it to my local cabinet maker and asked him to round the top sides so the the thread would run a bit easier over the wood.

villageweaver (not verified)

why don't you cut a swatch, measure it, then put it in a bath of hot, soapy water and twist it, wring it, agitate it, dry it and re-measure? that should speak volumes!

Bonnie Datta (not verified)

I have found that as long as I don't mix different wefts in stripes, the rug might get smaller and thicker when washed, but it stays flat and rectangular.  (By "different" I mean different fiber, weave, thickness, pre-weave treatments like washing, etc.)

However, washing the fabric before you cut it into strips may soften it, and that would make the strips easier to pack in.  So that is what I would recommend in general.

Bonnie.

Mary C (not verified)

Thank you both for replying!  I did try weaving some short strips and if washing it first makes it softer and easier to pack that's what I'm going for - it's into the washing machine.  That should also help get out any nasty things that I don't want to breath while ripping.  Meanwhile I have some nice t shirts I can distract myself with for a day.

Thanks again, Mary C

Mary C (not verified)

Well, as it turns out I've decided to change the warp colors before I use the material I thought was wool.  Someone suggested that I burn(with a match) a corner of the fabric.   Here's a link to how the burn test works:  http://www.fabrics.net/fabricsr.asp

Guess I have polyester after all...

MRD (not verified)

I really like the hair. How did you do it?  It gives great texture to the piece.  I have to admit faces are not my favorite things to do. They kind of make me nervous.  Yours is very amusing and I like the title.

Mary

jemwork (not verified)

Thank you for the comment. These were made with thrums, so the color changes came pretty fast. I wanted something that would stay in securely, but allow a couple ends to be free. Soumack! I threw one or two rows of plain weave in between to hold the loops, which I formed randomly with my fingers.

By the way, the face is woven with paper yarn.

Joan in Joamestown