Moe Sherman (not verified)

Hi - I'm thinking of buying a Compu-Dobby and am leaning towards the WeaveBird just because it's Leclerc and I love my Nilus. LOL I'm planning to test weave different brands while I'm at Convergence. A concern of mine is problem solving as I live in Colorado and there is only one LeClerc dealer and they are on the other side of the mountains. With that said, I intend to be a lurker until I actually buy one.

 

monach (not verified)

I own an older Weavebird: purchased 8/11/2005.  I stopped weaving in summer of 2009 because I became frustrated with all the jams and lack of technical support in Western Colorado.  I have recently found the Leclec trouble shooting guide online, as well as joining complex weavers, and learning about you.  Francois recommends upgrading my loom with the new cable system.  I am able to get the lifting cables for the shafts in balance when I have those type of jamming problems, but now I think my problem lies in the loop cycle, which is the treadle cables.  I don't have the newer treadle cable turnbuckels, so I can only make so much adjustment.  I have shortened my R treadle which was hitting the floor by 1 "textsolve" loop.  Even still, every so often, I can feel that the loom is going to jam, and it is when the forks are open, so it doesn't make a full loop.  It seems to get stuck at the top of the  loop- the right treadle cable.  This is the one I shortened because it was resting on the floor.  Before shortening, I was getting a ton of jams, (partly because my #15 & #13 shaft cables were too loose, but partly because the right treadle cable was too loose.)  Well, #13 & #15 are adjusted, no longer jamming, but I still have the sticky loop cycle when the right treadle is depressed, just not as often.  Does it sound to you like I need the cable longer or shorter?  Either way, I need a fine tuning system, like the turnbuckle, because the textsolve loops don't give me a fine enough adjustment.  Please tell me what you know, have experience, or have heard about the Leclerc's newer cable system.  My husband is very skeptical, because the loom was so expensive, & I've had so many problems with keeping it in balance.  I need some feedback from WB users before I purchase an "expense fix" which may not fix the jamming/balance issues.

monach (not verified)

We have the same loom.  After beaming the sections, I go to the front of the loom and remove front cross piece, (it just slides off) and unscrew the wingnuts on the beater, removing them & the reed.  Then I get a low stool, so the warp is at eye level, & I can see the cross in my warp & my heddles.  I also use a clip on halogen light.  Threading quite easy once you get close enough to the threads.

monach (not verified)

Linda, to put a cross in your warp when you are warping sectionally, you need a tension box that will give you a cross as you beam.  I use an AVL tension box, which makes 1" sections.  After each section, I insert the cross into 2 strings which are attached to the castle.  I do not use lease sticks. For me, inserting strings into a cross is easier than inserting the lease sticks.  I learned to warp sectionally using Peggy Ostercamp's warping book.  It has many diagrams, and very easy to learn.

Andrew Kieran (not verified)

there oughta be a wee rigid heddle on the tension box. you can use that to add the cross with long strings. I don't beam sectionally but if I did, i'd do that and then put the lease sticks in afterwards and hang them behind the shafts to thread up. To each their own though.

TinaHilton (not verified)

If you live anywhere near central Indiana, Robert, you should make a trip to Tabby Tree Weaver.  Linda Adamson is the owner and is very knowledgeable about looms and weaving.  She is a dealer for many of the ones you mentioned, including Louet, and has several in her shop that you can look at in person.  She's just north of Indianapolis in Arcadia.

I've owned looms from several manufacturers, but not Louet, so I can't give you opinons on it.  I do know that my opinion of the "perfect" loom for me has changed again and again as I've progressed in my weaving life.  I'm pretty happy with the mix I have now, but it's taken 6 years to find them.  And I wouldn't be surprised if somewhere down the road my needs and interests change and I'll want to change looms again.

Tina

jeannine (not verified)

hi Ellen ,I am not an expert but I think  you can weave bands in supplementary warp weaving on an inkle loom.As long as you can weave weft faced weaving and are able to easily acces the full width of the warp for the inlay it must be possible.

 

Ellen (not verified)

Ok, thanks for your encouragement, all.

I'll have a go after I have finished these towel-straps, then. Will have to find some thicker yarn, though. I have been weaving with very fine yarns for a long time, so my stash is all like silk 60/2 up to cotton 16/2. Won't do.

I'll let you know how it goes.

Ellen (not verified)

Ok, Laverne. I'll choose a motif where that is not a problem.

And don't worry, I'm a dedicated follower of your group :-)

Ellen

rose Goldielocks (not verified)

I have only one warning about using an inkle loom for backstrap weaving.

If your inkle loom is not built strong enough to do cardweaving ; DO NOT TRY DOUBLE -WEAVE on it!  you will break your loom. I had problems changing sheds and keeping proper tension on my band I was working with double weave on a double-sided inke-loom, and finally swiched it to rods to use with a  backstrap.  (I have broken more hardwood inkle looms that way!)

However, all of the rest of the techniqhes can be done just fine without breaking an inkle loom,  the warp pickup designs, supplementary warp, ect. In atwater's book "byways of weaving" and on the atwater monologe on inkle weaving (avaliable at the arizona site as a free PDF) those techniques are described in much detail with fun patterns, both easy and challenging to do.

Sharon