mischiefmanaged (not verified)

I'm pretty inexperienced also, having made only a few projects. I estimate my amounts of warp and weft for backstrap weaving the same way I did when I did rigid heddle weaving. I think you could use the same formulas as your sister although there is less "loom waste" with a backstrap loom than with a floor loom because you don't need as much extra yarn for tying on the warp. You need to be able to wind a warp on pegs the full length needed including the loom waste and takeup.

No worries about asking elementary questions and don't apologize for posting again! We all learn together here.  There are a lot of very helpful FAQ topics in this group, and welcome.   :)  Cindy

rose Goldielocks (not verified)

when I figure amounts of yarn for a backstrap project (or an inkle weave project), I take my finished lenght that I wish and mulitply it by 1.10 or 1.15 (you use the bigger number for larger diameter yarn, and the smaller number for finer thread.

At the end of the project, When I am all done, and go back and check if my numbers were correct, I find that the actual numbers were about 1.07 to 1.12... but the larger numbers gives you some 'fudge factor" or a chance to weave an inch or two of 'wonky' weave to decide how tight to pull the weft.

so... if I want a 24" table runner with 3" fringe.. I do the math like this:

3+24 +3= 30"

(30" ) * (1.12) = 33.6   [ * is multiply on keyboard]

so I will warp at least 34 inches, but probbly will warp 36"...

now, you take the 36" and multiply that by threads per inch and width of project.

 

so... 36 * 20 threads per inch * 8" =  5760 inches

 

5760/ 36" = 160 yards. ... so look for a ball of yarn that is longer than 160 yards.

Remember... yarn is just like lumber... you can cut it shorter, but not longer. Do you rember the joke about the mythical "board streacher" that the experienced carpenters send the new guy for when the new guy cuts the board an inch too short?

rose Goldielocks (not verified)

the above measurements were for the warp only...

you also have to do the weft"

 

(for weft faced fabrics, your picks per inch will be between half and 0.75 of your threads per inch)

 

24 inches x 15 picks per inch x 8 inches wide = 2880 inces

2880/ 36 = 80 yards weft...

 

so total yarn for project = 80 yards weft + 160 yards warp = 240 yards total needed

so.. buy twice that amount of yarn if it is inexpensive... (2 balls of merciededs cotton)... or 1.5 times the total if the yarn is expensive... so 360 yards of expensive yarn.

hope that helps... of course you have to do this for each project... or you just get a "feel" for how much yarn you will need.

Sharon

siseltikva (not verified)

That is so helpful! Thanks so much!

Thank you for the example, that's really helpful. I can't wait to try everything out! 

OCF (not verified)

Thank you for the information about measuring out yarn. I am just about to begin weaving for the first time in my life and have just ordered a 24" Rigid Heddle Loom. Would the measurements above till apply? Also, and this is pure ignorance on my part, what does the 8" number refer to? I kind of understood all the rest of it.

Thank you for your patience in answering this completely novice question.

whiteoakgrandmother (not verified)

The "8" in the example was the width she was using, you would have to multiply by the width you want. Backstrap and inkle looms have less unweavable waste at the ends than a rigid heddle loom. You will need to determine how much waste your loom has and add this figure to your warp length. If you tell us what loom you have ordered, someone here probably can tell you the waste length.

claudia (not verified)

I received my loom and beginners kit as a gift 2 years ago. My friend did all the research and bought everything from Mark Deschinney in Window Rock, AZ. When we were there in September 2009 we met him and saw his work/living space.  He also makes fabulous Navajo spindles and I bought one from him. He doesn't spin so I had to find a Navajo woman to teach me and we met a family of Navajo weavers and spinners at the trading post at Two Gray Hills Toadlena Trading Post. I wrote about my visit here if you want to take a look and read about my experience.

All that to say I have a 2" fork and a 1" fork and use the larger one most of the time.  I bought the smaller one because I was at Toadlena and wanted to get something as a useful remembrance of my visit.

Claudia

craigeann (not verified)

Your comments about the forks were very helpful. Thanks

alsnipes (not verified)

Mary,  I use to leave the tines on my comb sharp on purpose. For the past year or so, I have been rounding the tines slightly because of a concern for safety.   I asked many many customers about the sharpness and was told it was no problem.  My thinking is that many weavers perfer the tines sharp and I get so many complements on that.  For those who perfer duller tines, it only takes a few passes with 220 grit sand paper to round them off slightly to the weavers liking.  The combs are finished with danish finishing oil, so that the finish can quickly be referbished by use of tung oil.  The combs I make for Cactus Flower Looms have 7 times per inch per her request.  I usually refer to them as finishing combs.   I make many different sizes of combs.  Most combs have 4 times per inch.   If you wish you can visit my Facebook photo album 'Snipes Weaving Tools' to see all of them.  Combs range from 1/4" to 1 1/2" thick, 4" to 12" in length, and 3/4" to 3" in width.  It is all what the customer wants.

You have a great day and enjoy your weaving experiences.  Al Snipes

alsnipes (not verified)

Laverne,  Though it doesn't appear as such from your photo, the tongs are spaced approximately 4 tongs per inch when measured from the outside edge of the outer tooth.  Each tooth consists of two parts...The tooth and the gap to the next tooth.   That gives you the 4 tongs per inch. Hope this helps...