Bruce McLaughlin (not verified)

Tina--Sorry for the late comment.  With narrow warps and using a flyshuttle, the warp should be "off centered" 1/2 the length of the flyshuttle you are using.  If the flyshuttle is 12" long, the warp should be off centered 6 inches (that would be 3 two inch sections).

I have successfully woven many handtowels at 21" wide (on a 48" AVL) without "off centering.  Scarves I usually do at 11" wide and always off center them.

 

alison.addicks (not verified)

Shim the reed: if there's gap or uneven spot between the end of the reed and the box, the shuttle can launch into the air.

TinaHilton (not verified)

It seems to be resolved.  I make sure the reed is centered, so there's no gap at either end.  And I moved the warp over 2 sections (4") instead of one like I did before.  I haven't had it happen once on the 18 yard warp that's almost finished.  

I'm still trying to work out the best way to pull the cord on the flying shuttle.  I actually burst a blood vessel in my thumb, apparently from too much pressure there.  So I just changed the way I hold it and it's going better now.

Thanks for all the advice.

Kristina (not verified)

Hello Gail,
 
I've always tried it so ,that the  hair comes over  the both edges as shown in the picture

It´s not my fabric ( I found this picture in www), but it clearly shows that the warpthreads should be collected at the edge closer to ensuring the fixing.

 On Kerstins blog ( she wrote the article  at vävmagasinet you can also see an edges with horsehair  like this : http://oddweavings.blogspot.com/) I have not so many experiences with weaving horsehair to make a propper planing before . So I think best way would be to weight a fabric , so you can caculate how much hair you will need. But I would always choose a thinner yarn for the warp, to bring out the horsehair character.

I hope that helped a little. But I think a better adviser in this questions  is kerstinfroberg, she`s a weavolutionmember.

Kristina

 

Caroline (not verified)

just a thought, why not crochet an edging?

Seriously, I think I get into more trouble with my selvedges when I think about it. My current project is a sari silk bag on the Knitters Loom. I am spinning the yarn as I need the colour runs, but even after torturing the silk through the hand carders its still a bit textured, and because I have overspun it a bit so it doesn't fall to pieces, the selvedges look terrible:

Some of it is because its really uneven, and at other places its because there is a knot or fuzzy bit at the edge, like the one you can see in the picture. The only thing in its favour is that its consistent, so I'm hoping I can somehow disguise it once I put the bag together. I do find it easier to make consistent edges if I ensure the weft bubble is pretty much the same each pick, easy to do with a weft-faced weave, but it seems to work true for balanced weave too. I do hold the side of the fell so it doesn't drag and distort as I place the weft, and once I start beating the weft I let go, and start placing the weft from the yarn/shuttle side and work back, checking its not pulling as I go.  I also change shed before I start beating or use the RH to place the weft. I might end up with too much weft at times, but thats easier to sort than when its pulled too tight.

But you are probably doing all this anyway! Worrying is going to make it worse not better, because with the best will in the world you will tense up, and this follows through to your weaving. If you concentrate on achieving consistency in the arc of the weft, you will find the selvedges take care of themselves and it all settles into a regular pattern.

I take it you prefer weaving on your Baby Wolf to your Rigid Heddle loom? Perhaps its time to just play with the RH and see what happens, instead of trying to do a specific project with a specific outcome. Make your sampling fun.  Once you have made friends with the loom instead of fighting it, you will wonder why you even had this problem.

HTH.

sandeleh (not verified)

Claudia, I've done a lot of weaving of scarves on my RH loom and have pretty good selvages (so far, anyway).  I suspect your edges on the sock yarn stem from a too-loose sett.  I have always woven my sock yarn projects at 12.5 epi.    I also add the step of laying down my shuttle and making sure the weft is at as steep an angle between the fell and heddle as possible.  Then I beat with both hands on the heddle to make sure the fell stays at a 90deg angle to the warp ends. 

I've left the photo above rather large so that you can see the selvage on the blue scarf - it is pretty even, I think.

 

Above is a photo of my Woolease (warp and weft) scarf on the RH using my 10dpi heddle.  The Woolease is nominally a worsted weight yarn and actually very much thicker than sock yarn.  It behaved well for me in the 10 dpi heddle and you can see the left selvage pretty clearly - it's pretty even looking.  (The yellow ribbon on the right is my measureing tape)

I have not woven very much on a floor loom, but I think the motions needed to get good selvages differ from those needed to get a good selvage on the RH loom.  I find that my lack of experience with boat shuttles leaves my selvages looking a bit ragged or worse!  LOL.  I suspect that my selvages will improve with more practice.   And I think if you spend a bit more time on each pick with your RH your selvages will look a lot better very quickly.

Sande in Fresno, CA, USA

 

KSfiber (not verified)

I've woven a lot of sock yarn scarves on my rigid heddle loom using a 10 dpi reed.  I like the drape they have with the open sett.  You do need a light touch when you beat.  Like don't think of it as beating.  Think of it as pressing it into place.  Count your picks until you the the idea of what it looks like too.

I go slow on a rigid heddle loom.  Maybe that helps my selvages.  I know it keeps me from over beating.  I put my shuttle down before I beat & change sheds too, using both hands to keep the fell line at 90 degrees to the warp.

 

sandeleh (not verified)

Sorry for the big photos, Laverne, but I wanted to be sure that the selvages would show up well.   I hope the wait was worth it.  :)

Sande in Fresno, CA, USA

 

claudia (not verified)

I know the big photos cause havoc for the dial up folks but I appreciate being able to see your selvedges.

I am caught between liking the drape of the sock yarn warp at 10 dpi and finding it a bit fussy to work with. Like KS I put my shuttle down and gently place the weft in being certain I have it at a 90 degree angle to begin. Once I got going, the scarf came out really nicely. It's just different working with the sock yarn. The heavier yarns are easy by comparison.

Thanks for all the help folks. And, as always, it means a lot to be able to see the pictures. Your scarves are really lovely Sande.

Claudia

sandeleh (not verified)

Hi, Claudia  (and thanks for the kind words!)

If you are putting in the weft straight across the warp before you beat, that could be the cause of your selvage problem right there.  The weft wont have enough length to beat in well if it is straight across the loom and leaving extra on the leading edge will make for wavy edges.

Instead, place the weft at as steep an angle as you can from the fell at leading edge to the heddle at the exiting edge.  I push my shuttle thru, then put it down and place the weft by hand, holding it where it enters the shed at the selvage then using other hand to make sure the exiting end is as close to the heddle (still in blocks) as possible.   Then I beat using both hands on the heddle. 

I attempt to move the heddle in an arc so that it beats at the fell on a closed shed, then continue the arc to open the opposite shed while returning the heddle to the opposite position on the heddle blocks.  I find this arcing movement places the weft nicely and clears the opposite shed if the warp is a bit sticky.

I'm sure that the more you practice the better looking your selvages will be.  :)

Sande in Fresno, CA, USA