DianneStucki (not verified)

It's a rectangular frame, with dowels to attach fabric to, and then you roll the fabric onto the dowels as you work. I'm just wondering if the tension would be strong enough. Tension is adjusted with wing nuts.

Caroline (not verified)

I cannibalized bits for a backstrap because they have this really convenient notch in them to hold the straps in place. I suspect that unless you have longer side pieces, you could find the length very constricting, but I see no reason in theory why it should not work, as long as you can hold the web under constant tension - some frames are better at this than others so it could be trial and error to find out.

Let us know how you go!

jenadina (not verified)

Laura, you might want to contact Abby Franquemont...I know she's done some weaving with Z and S twist yarns on her backstrap loom. I'm pretty sure she used doubled yarns (not plied, just doubled), and very high twist (important on the backstrap loom), but she might have some insights for you.

~Jen, your friendly neighborhood spinner ;)

Alison (not verified)

Hi Laura,

I assume you want balanced yarns, one S and on Z  that can be used for the warp?  So you're really looking for at least a two ply yarn.  My thought is that you'll get a more distinct S or Z effect with a two ply rather than 3 or more.

A few tips for spinning for weaving.

1 you have to be careful with your joins because if not done right, they will fray in the heddles and reed.  Texsolve may put a little less stress on them, but it is something to think about.

2 you can test your yarn as a warp by using the friction test.  some people use their fingernails, I think I saw one person use something like a paper clip. 

3 You noted in another thread that worsted spinning will show the effect better.  I think you would get the effect with any evenly, smoothly spun yarn, but concur that worsted should show it the best.

I'm sure I'm forgetting something - it is rather early and I've had very little sleep, so if I think of anything else, I'll write.

dteaj (not verified)

Laura,

Just wondering if you've implemented your S & Z experiment yet...

Debbie

dteaj (not verified)

Laura,

Just wondering if you've implemented your S & Z experiment yet...

Debbie

FiberVoodoo (not verified)

If you wet finish your "energized singles", they won't work as well in the cloth (make puckers, ripples, etc.)  The best way to do it is to follow Kathryn Alexander's lead, and leave them on the bobbin, or wind them off onto toilet paper rolls.  Don't get them wet.  They need lots of twist (can't tell from the photo, but it looks like it could use some more).  The twist will relax on the bobbin/tp roll, making it easier to work with warping and weaving.  AFTER it's woven, place it gently in warm water and watch the magic happen (you know all about that!).  Don't full it, as the puckers and ripples will be reduced.  There are articles in older Handwoven magazines that cover "collapse" cloth, which is basically what you're trying to do.

Good luck!

Laura Cunningham

dteaj (not verified)

Hi Laura,

I'd love to see what you have done with differential shrinkage. I'm working on this quite a bit right now and have recently joined the CW group devoted to the topic.

Thanks,

Debbie

mischiefmanaged (not verified)

Thanks for this. I have a warping board but did not know how to start or end for a continuous warp until I looked at the diagrams. I have wound a smooth cotton warp for my 2nd try at backstrap weaving, so I am keen to get to it!

Do others use a warping board? I have a bit of trouble spreading my warp out on the bars after it is jammed together on the warping board.

mischiefmanaged (not verified)

Thanks for the link to the photo instructions; I'll use them when I've gotten a bit done. My first warp was the sticky one and I only wove about 2 inches before deciding I needed a friendlier warp ;) I hope to have something to photograph later this week. Cindy