siseltikva (not verified)

I'm so bummed, I started weaving on the warp I started to do the warp float project, and I am literally unable to pull up the shed stick (the one that's not the string heddles). I'm using the same yarn for my string heddles as my warp string (mercerized perle cotton #3). I do have some 5/2 perle cotton on the warp, but I didn't think that would cause that much of a problem. I know there are some loose warps, too, but I've taken most of that up with dowels.  

Is this the "sticky warps" problem I've heard you talk about? Maybe I just forgot how of weave. This is also wider than a lot of what I've done, but surely its not just that. Do you think its my string heddles? I have some nylon string that I could use, if I could reestablish the two sheds, but its a bit thicker than even the 5/2 cotton. Will that be a problem?

Thanks for your help, as always! 

Tara

siseltikva (not verified)

Oooh I didn't want you to say "crossed warps." :( 

I tried your tactic of raising the warps section by section, and they seemed to slip past a bit more, but they still weren't very open on the nearer side of the loom bar. (Like, the cross barely made it past the heddle strings) So, I started looking carefully at my warps, and they are crossed, and loose. I thought I was so careful when I was warping, but whole sections (when I switched colors) are looser than the others. :( And because I had to rearrange them, with them not being tight they want to go back to their old arrangement.

I tried straightening them out and weaving again, and it is just too hard to get them to work as they are right now. I have wove maybe 6 rows all together, and that spent all my strength and patience. I might try to tension the loom (like between two chairs or something) and try to figure out where the loosest warps are and try to retie them. They are so loose, they are past being helped by a dowel.

The video did help, though :) Thank you! It is good to see someone else working with their loom, definitely, and seeing the work that goes into raising those sheds.

I'm fighting the desire to give up on this warp! I think it would be lovely if it worked and I would hate to not use all that yarn.

Thanks for the help! 
Tara

 

siseltikva (not verified)

Thanks again for your help! Since then, I've taken the wonky warp off my loom and started again. I was VERY careful when I was changing colors to keep the tension the same this time, but soon realized that my warping "pegs" are leaning in on my bookcase! That would have been a big contribution to the last wonky warp. I guess I hadn't had a problem with it before, because when I'm not weaving a wider band (this one's around 2.5 inches wide) I can stick them farther in my books where they are less likely to move. I also think I was putting more tension when I was warping, in an effort to keep tension the same, so that probably made them lean more. So, I'll have to find another place to warp than my trusty bookcase for wider things, but that's okay. I'll figure something out.

I also wanted to be really careful about crossed warps this time, and so far so good! I pulled on the yarns one by one when I was creating the new crosses, to make sure I was getting the right one. And I tried to be really careful when I was making my string heddles too. Which are never even, by the way :) Maybe in time.

All that to say, I let my loombar take up the lopsided tension, and I have successfully woven the foundation rows for my warp float pattern! :) With no silly crazy loose warps or crossed warps :) I can't wait to get to the patterning part, hopefully tomorrow.

Thanks for your encouragement and help! I'm very encouraged to be happy (and not frustrated) while weaving again.

rose Goldielocks (not verified)

If you don't have dowels available for a warping board, or don't have access to a power drill, you can use "L" brackets or braces to do the same thing and just screw them to a flat board. (now the posts are straight and perpendicular!) My biggest problem when making warping boards and stuff, was that I could not drill a hole 90 degrees perpendicular to a board with a hand-held drill. It always, no matter how hard I tried, ended up wonky and crooked!  Buy some sandpaper, or use an Emory board to smooth the edges of the metal braces to make sure that there are no rough edges.  The red dots on my sketch are the holes where screws go into. If you set the braces a little bit  in from the edge, and use a bookshelf board, the warping board can live in your bookshelf when you aren't using it!

As Laverne has shown ; a well wound, good warp is the start to a successful project.

Bonnie Datta (not verified)

Another possibility is an arrangement used a lot by tablet weavers.  C clamps are put upside down on  bench, table, counter top (whatever).  The shaft of the clamp works as a post, and with just 2 of them you can still make a cross.  You have to tighten them hard so be aware that they might leave marks unless you put something between to protect your surface.

Bonnie.

 

rose Goldielocks (not verified)

I have used that often.. but...

1) be sure to put a folded paper towel on BOTH top and bottom of where you are going to clamp; because unless you tighten the C-clamps to the point they leave marks, they will lean in to each other, especially if you set them more than an arm's lenght apart.     I have yet to wind a cardweaving warp where the left side is not a different length from the right side. Because I normally mount the cards in a table loom setup and tye off the ends in a conventional weavers knots and use header sticks, it doesn't matter to me if its uneven, but it would make any backstrap warp un-manageable.

2) any thread smaller than 'yarn'.. ie. that is 12 tpi or so... has a tendancy to get caught in the 'screw' part of the clamp.

If you are going to buy  brand new "C"  clamps... be sure to get at least the 4" clamps,  because the most common arangement you find is a 2x4 forming a ledge for a table (like a picknick table). a 2x4 is 1 1/2" on the supposedly 2" edge, and then you have a countertop (another 1/2" normally) on top of that.  (says the person who's clamps did not open wide enough for a demo, and had to find anther solution.)

If you keep your "C" clamps with your loom, you have an instant place to 'tie off' your loom in most city parks that are all grassy without any good trees. A 'normal' picknick table made out of metal or wood is generally heavy enough to anchor a loom to.

 

siseltikva (not verified)

Thanks for those ideas about creating warping boards. The L-brackets seem like a great idea. You don't have to work to get those perpendicular :) 

I thought I'd show you some pictures of my warp float practice which I just took off my loom. It um... well it doesn't quite look like it should. To be honest, I even have a hard time seeing the pattern and I'm the one that put it in there. I think its a combination of things, like the warp that's floating is bigger than the background warp. And that section of yarn is just looser than the other two sections, so it really floats away from the background. And my rows are too "tall" - I mean I should have decreased tension and beat harder. But. It's done. And I'm happy-ish with it, even though it not quite right.

  

Ps. The pattern is supposed to be the last on on the right here:

siseltikva (not verified)

Hmph... I wonder what I'm doing wrong then. Weird. When there was more than one row of the same warp being picked up on the pattern, that's when it floated over more than one teal stripe. So apparently I'm missing some step when that float should be going back into the purple stripe before it floats over the teal stripe again. I'm going to watch your video and again and try to figure it out.

siseltikva (not verified)

Nope, I have no idea what I'm doing wrong. I watched your videos twice, and read through the tutorial twice and I can't find the step I've missed, or what I have out of order. :( I tried to go back over the steps I went through when weaving and... nope. Can't figure it out. It seems like... I'm missing some step where the previous row's warp floats should be transferred back under the teal... :( I don't know. I hate it when I make fundamental mistakes like this.

Any thoughts? 

:) Thanks, though, for the edges complement! Its amazing what happens when I don't worry about them.

siseltikva (not verified)

There's nothing different in my process (from what I remember, at least) than yours.

Maybe I'm reading the pattern wrong! If the pairs I select should not be selected again in the next row, then I'm DEFINITELY reading the pattern wrong. Should I be kind of skipping a line? ... If that makes sense. Like, I shouldn't be picking up warps for every row in the pattern. Every other row should be the all pink row. ... is that it?