Hi all,

Recently I built my wife a floor loom and we have been looking for projects. I am a guitar player and one type of cloth that is interesting to me is what is used on Vox amplifiers. I have included a link to a forum post (around halfway down the page) which has a zoomed in photo of the weave. I believe (though I am quite the novice) that the warp goes from right to left in the images as shown. What would be the best way to achieve this sort of weave? I have some ideas but they all seem very complicated.

Thanks for your help!

Nathan

The link: http://forums.vintageamps.com/viewtopic.php?f=2&t=36562

Comments

ReedGuy

It's been stitched into the cloth. If the cloth is a simple plain weave the warp sett would be open, but to keep the weft spacing open you would not beat it tight. You could maybe insert a piece of fine wire every other weft shot for the spacing, and after 5 or 6 of these remove the first and use over as you go along. You want a yarn that is not smooth, but kind of hairy like linen that would help bind the yarns, since it's so airy. Linen scrim for upholstery has one wieght that is airy to bind seat springs.

I'm not too sure it is a regular plain weave here, instead some type of embroidered cloth. I have speaker cloth here, that is definitely not loomed in the sense you are thinking of on a foot powered floor loom. It is too complicated. On your loom the warp and weft are at ninety degrees.The diamond pattern there is at 45 and 60 degrees.

pammersw

I've seen something somewhere where you could weave a design like this in as you go, but this isn't made that way, as near as I can tell. It's an overall quilting-like embroidery pattern. With care, you could do it with a regular sewing machine, but it would be easier and more accurate/precise to find a computer-guided quilter and have him/her do it.

kerstinfroberg

To me, it looks like the ground cloth is an overall leno (or gauze, if you prefer). I agree with the others: the "decoration" looks like it was added afterwards (or would have to be, for us handweavers)

IIRC, Sharon Alderman (http://sharonalderman.com) used to weave bespoke "speaker cloth" (for jukeboxes, maybe?) - I can't see it on her website today, but you might contact her?

laurafry

Kerstin, I had the same impression of it being Leno weave but could not tell for sure. Cheers Laura

NateM

Thank you for all of the comments everyone. I did wonder if the diamonds were more of an embroidery than an actual weave but I was unsure. I will keep on investigating this and see what I can come up with. I will also take a look at Sharon's page to see if there is any additional information there. Thank you for the information about achieving the open nature either through inserted wires or a Leno/gauze type weave. I will keep on researching!

Thanks again,

Nathan

sally orgren

What if the photo of the fabric was turned? (Those supplementary red, green, & white threads were actually warps on separately weighted bobbins, hand-manipulated at the front of the loom?) 

sally orgren

What do you think with the rotated view?

ReedGuy

Hard to say really, but I'm not so sure it's even leno weave.

laurafry

I'm not sure what it is, but a leno weave would make structural sense - a nice open *stable* mesh....

cheers,

Laura

Sara von Tresckow

Turned, it certainly looks like overall leno (would give stability to the open structure) with supplemental weft threads.

Looks deceptively simple, but most likely woven on a loom with special setup.

mneligh

My guess is also leno, but what about the diamonds?

I believe you can do this type of leno -- "doup leno"? -- on a loom with the special special mulit-part heddles made for this purpose.  I have a pamphlet on it somewhere, and have contemplated getting enough of the heddles to try it.

Looking at the back as well as front on the website, though, it looks almost as if the diamonds were woven in, but I don't think it was done as a lappet technique unles the thread on the diamonds is discontinuous.  At any rate, I can't figure out how one would do it.  

How would one mechanically embroider on the surface of leno? 

mneligh

Now that it's rotated, I can see that I could duplicate it with supplemental wefts on a leno base.  

Diane Parrilla

I am new to weaving.  I just purchased my first floor loom. The loom has 10 treadles.  I assumed that it has 8 harness but come to find out it has 4 harnesses.  I    have researched harness kits and they cost much more than I paid for the loom.I was hoping since there is 10 treadles maybe that would reduce harness upgrade cost. Would appreciate advice

 

 

.

Diane Parrilla

Is it possible to warp a sectional beam in the traditional sense without the use of bobbins?

mneligh

You can wind narrow chained warps the width of each section, and beam them independently.  I frequently do this.  You need a tension box or other device to comb and tension each section as you wind on.

Diane Parrilla

I am sorry for messing up my texting.  I am new to this.  I could not get my wording lined up with the blinking line.  Please omit this message and I will write another one.

 

 

 

 

 

 

 

 

 

 

 

.  How do I do so?  Does it matter what the make of the tension device I use (if I do indeed purchase one)I just purchased a 45 i

 

Stockton Ca.  Do you recognize the label?  Is this a gilmore loom?  Another question why would there be 10 treadels and only 4 hat

 

Diane Parrilla

I am trying to determine make of a 45 inch jack floor loom I just purchased.  Underneath loom it says " handcraft studio made in Stockton Ca." Does anyone know of this info?   Another question why would there be 10 treadles and only 4 harnesses? I am a be ginner ignorant weaver and need all the help  I can get.  I am hoping that since there are 10 treadles will the upgrading process

Artistry

I think this is a very open plain weave made with something heavy like Jute, but open enough to let sound out. Then as Sara and Kirsten say a supplementary weft. There would be many threads to weave in at a diagonal. This reminds me in a way of a Huipil, which of course is done on a backstrap loom. I'm not suggesting this is done on a backstrap! I don't know how to hook up a link but search Huipil, you'll see Karren Brito, on her projects page there is one. Different technique but maybe similar process.

ReedGuy

If the loom was used, the extra shafts might have been misplaced. I guess we have no idea how much was paid, but I wouldn't think shafts were that expensive to buy. Depends I suppose what goes into the manufacture and demand. It may be difficult to obtain used. One selling a used loom usually sells the whole thing, not sections of the main loom. Maybe a sectional beam or supplemental beam, but not usually the shafts. Odd situation, you would think there was 8 shafts. Where you told the loom had the 8 shafts and received otherwise? or just an assumption?

Diane Parrilla

The person who sold the loom had absolutely no knowledge of the loom. I assumed that it came with 8 shafts.  Dissapointment hit me hard when I found out that there were only 4 shafts. I have done some research and have found out that harness upgrade kits (4-8) cost  $800.00.  I am hoping that since the treadles are set up at the 10 peddels that there would be a reduction of upgrading harrnesses.  I'm still trying to determine the maker of the loom.  I think it is a Gilmore loom.  Thanks for responding. Need all the advice I can get.

ReedGuy

It is pricey, but yet a new floor loom can cost thousands. No experience myself with jack looms so I don't know all the details in the shafts to manufacture. I know on a countermarche I made here, there isn't much to it at all.

Diane Parrilla

You mean to tell me that you have constructed  a cm loom from scratch ?   My husband is pretty handy and I was wondering if the shafts could be hand made?  The mark up of parts for looms is incredible. That is a huge cost reduction if a person could build or make thier own parts(in your case a loom). Thank you for the info.

pammersw

Take a look at what you have. If the channels are there, the harnesses are basically frames with metal pieces flexed in near the top and bottom. Shouldn't be hard to do, with the originals there for comparison and measurements!  A little harder if you need to make the channels,  too, but very doable.

Diane Parrilla

Thank you for your input.  I also have a tissart rug loom. The loom has a sectional beam on top. Am I able to attain a tight warp for tapestry weaving using the sectional?  I do not have bobbin rack or a tension device. A reply to my former question mentioned that I could get by without the use of bobbins but I would need a tension box or device to comb out the sections.  What is the alternative substitute to maintain even tension if I do not have a tension box?

Diane Parrilla

I am fasinated with the art of navajo weaving.  My husband is currently constructing a loom for this.  I am looking for a book that contains mainly rug patterns.  Does any one have any suggestions as to the name of a book that offers a large  variety of rug patterns.  Thank you.

 

 

mneligh

The reason to use a tension box is that you are winding each section individually, and you want uniform tension across the width.  This is difficult enough to do if winding the whole width at once -- that's why people have all sorts of methods ranging from warping trapezes  to weights to tugs, etc. to get the tension uniform.  The other reason is to comb out twists, knots, etc.

While classic sectional warping does not use lease sticks, I would use them if not using a tension box.  They will more or less comb out the warp and assure that it is packed flat, not lumpy, into each section.  I would also use something as a warping trapeze -- a rectangular table turned on its side (or not, depending), the top of a door, etc.  I would also use a can of soft drink, an 8 - 16 ox bottle of water, or the like put in a garbage bag.  Tie a slip knot in the warp through the bag after it has passed over your trapeze so that the weight (bottle or whatever) hangs just off the floor.  Start beaming the warp onto a section, and continue until the weight is about to pass onto the top of the trapeze.

You could also save up until a used AVL warping wheel becomes available.

barleycorn

One place you might want to look at is Dover Publications. They have a few navajo pattern books at a very reasonable cost.

ReedGuy

Diane, yes I have built a 62" (inside) wide CM loom. That was only the beginning. Build a lot more weaving 'stuff' besides. As of this winter, I now have two warp beams to. :)

Diane Parrilla

Thank you so much for info.  On those sticks what are the measurements of this?  Also how would an avl warping reel help?  From your suggestions it sounds like it would be so much easier to purchase a tension box and use that. I am already looking into a used tension box to buy . Thanks again so very much..

Diane Parrilla

You are so fortunate to be able to build looms and parts yourself.  What an incredible savings!  What a gift you that possess that you can build a loom completely by yourself .  You make the beams too?  Good going.

ReedGuy

Yes, I made the beams. And I also made sectional rakes (U shaped). The second beam is supplemental with flanges that others on here talked me into and showed me. ;)

mneligh

If you're using lease sticks to warp a single section, they only need to be slightly longer than the section is wide.  That is, you have to have some means of securing the ends, such as holes.  Any flattish, smooth, lathing an inch or so wide will work.

http://www.avlusa.com/catalog/warping-accessories/warping-wheel/videos

The insert link thing doesnt'w work in my browser, so here's the URL.  Watch the video on the AVL web site.

The AVL warping wheel allows you to wind the warp on the wheel, and then beam directly from the wheel via a built-in tensioner.  It is expensive and takes a lot of space, though.

ReedGuy

If you want to hold a cross for the entire warp width, use a lease string that you insert when each section is fully wound. Then when the sections are all wound you can put full width lease sticks in. I do, some may not. However, many do. :)

Diane Parrilla

I appreciate everyone's help so very much.  I am unable to attend classes due to medical issues so therefore, I rely on books and the you tube for teaching reference.   This is a wonderful source of information being able to ask questions from all of you.  Thanks again.  I know I have a lot to learn.  For some reason when the weaving bug hit me ( I eat sleep breathe weaving it is all I can think about ) It hit me hard .    Crazy

        Thanks all!!!!

 

 

 

 

 

 

 

 

 

Diane Parrilla

My knowledge of looms is next to nothing and am hoping someone can help.  The tissart rug tapestry  loom that I recently acquired is quite different from the pictures of other looms that I have observed.  Instead of 2 pedals it has 3 pedals.  When the middle peddal is depressed a row of nails (underneath the red) pushes forward.  What and why is that?  The other tissarts that I looked at none of them have a sectional beam on top. Is that uncommon for a rug tapestry loom to have a sectional beam rather than a traditional beam?

Diane Parrilla

I am completely baffled of my newly acquired loom- whether it  is a tissart or a dryad tapestry loom?  The handle's  imprint says "lecleric"  so I assumed it is a lecleric tissart.  The loom's weaving width is 40".   Lecleric only makes 45" and 60".   I noticed that my loom is extremely made for sturdyness.  The lower cross wood beam is very wide not like the lecleric looms.  It has 3 pedals,the middle pedal (depressed) a row of nails ejects forward.  I do not know the function of these nails.  Does anyone have a dryad loom ?  Does it sound like this loom is a dryad tapestry loom. ( yes it is a vertical loom.  Are the dryads much sturdier than the leclerics.  I am starting to lean towards that it is a dryad loom.  Any opinions?

tommye scanlin

If you can post a photo of this loom perhaps someone will recognize the type. Tommye

Diane Parrilla

How do I send picture?  I tried sending picture and I can't because  pop ups (which I've been trying to fix for hours and unable to). keep preventing me from sending pictures

tommye scanlin

I can't guide you through the process but think it's addressed in the help link at the black menu strip at the home page.

Diane Parrilla

You're right.  I followed the directions and after I pressed the directed prompts a message saying " you have a pop up already open and cannot have another one open at the same time."  I've researched google - downloaded apps to close the open pop up to no avail. Is there an email that I could send the picture to?  I have tried and tried and I just can't close the darn pop up.  Thank you.

ReedGuy

There are two windows that open and must remain open to post a photo. The first one requests the link, which you don't have yet. But you click the icon to the right of the link field. This opens another, but the first must remain open. It should be behind the second one when it opens. Then the menus up top of window two had an upload buttom that opens a browse popup so you can upload from your computer. When the file loads, you click it in the preview at the bottom of window two. This sends the link the first window. You click in that window to send the link to you post. A requester pops up to ask if it's ok. Then it's in your post. And now the only window open is the forum page.

Hope that helps. If the file is too big (more than 600 pixels at the widest dimension) it will be cropped or purged and not loaded or only partially displayed.

endorph

and see if they can help you get the photo uploaded

sally orgren

I don't think the site is capable of taking uploads from mobile phones or tablets. When I try, I too am stymied by "too many windows open." 

pammersw

I can only upload to projects, then I can put a link in a forum post. This is from an Android tablet.

sally orgren

That is more than I am able to accomplish with my Android phone!

Diane Parrilla

Good thing I have a floor loom because now I understand from reading previous comments - the disadvantages of weaving on a table loom.  The table loom I have is a old (probably homemade) jack style loom.  The shafts - the way they rise and fall is very poor.  There are  no levers.There is a set of pulling devices(made out of wood) on top of loom that lift the shafts and not very well. Some of the shafts do not drop all the way down .  So I have decided if possible to make this a tapestry loom and exclude using the shafts.  Is it possible to attain navajo style of weaving on a table loom and if so do the ends need to be twined?The loom has a 12 dent reed.

 

 

Also do you use the first 2 shafts (with Navajo weave) or is it best to hand stitch the heddles?

 

 

 

Submitted by NateM on