Hi,

I am new here and I have had a search but haven't found an answer so I thought I would just jump in and ask.  Apologies if this has already been aswered and I missed it.

 

I have a four shaft Levard table loom, a no 13 I believe, and am using it for the first time.  It came without a manual, the previous owner had lost it.  I was fine, despite having switched the warp from a rigid heddle to the Levard, until I got halve way though threading the heddles (I was working from the back beam to the front).  I had followed instructions of dividing the heddles by 8 and putting 1/8 on each side of the four shafts, but then  I realised that because of the way the shaft bars attach the heddle bar to the handles, it meant that the warp wasn't even.  The bars are attached at different positions on each heddle bar, wth a difference of 2 3/4 between the first and last bar.

Am I making any sense? 

I am puzzled as to know how to figure out how many heddles to use on each side of each shaft as each one will be different.  Does anyone else have this type of loom or the instruction manual for a No 13?  Is there an easy way to do this?  Should I be warping front to back rather than back to front?  

Any help much appreciated!

 

Comments

Sara von Tresckow

Do it as I'm doing this afternoon.

Just thread your heddles in the correct sequence.

When finished, find the center of your warp. Now change the centering of your heddles to match that center. Then have fun weaving.

cyberbarn

Thanks, but how to I change the centering of my heddles? 

Sara von Tresckow

You change those points where the heddles are divided the same way as before, but with warp running through the heddles. That way you can easily see that the warp is running straight. For future projects, you can than estimate how many heddles are needed on each side of that attachment point.

You do not, at this point, have the reed threaded or the warp tied on so the threads will move around as needed.

cyberbarn

This is the bit I don't understand though, I can't change the points where the heddles are divided because they are blocked by the metal bar that attaches the heddle bar to the levers that raise and lower the shafts. I can't figure out how to get the heddles from one side of the shaft to the other. 

 

Sara von Tresckow

I'm looking at a photo of that loom. Its just a table loom. There are metal strips between the handles and the shafts that appear to clamp around the top bar of the shaft.

There is surely a way to temporarily disconnect this and arrange your heddles. Many looms are built this way. In each case, the heddles can only be moved from side to side when that offending clip, clamp, cup hook or whatever it is is disengaged.

jander14indoor (not verified)

I haven't seen your loom, but my Baby Wolf also has a support (unfortunately, NOT on center) that blocks movement of the heddles.  On that loom you can disconnect the supports and move them out of the way enough to allow the heddles to center as Sara mentioned.

But I find that a pain and only did it that way once or twice.  And I'm and engineer, use spreadsheets and math all the time.  So I just calculate the heddles needed on each shaft and figure out how many needed on each side of that support. 

If the pattern is symetrical its easy.  Use the threading draft to figure out how many heddles per shaft.  You need to do that anyway to make sure there are enough heddles on each shaft, many patterns tend to load one or two shafts much more than the others.  You can count manually, set it up on a spreadsheet like I do, or use weaving software.  Once you have the heddle count for each shaft, just divide in half and thats how many on each shaft on either side.

Unless you own a Baby Wolf or other off center support loom.  In that case you start by dividing in half.  Next you need to know how far off center the support is and what your warp ends per inch is.  Then the tricky part, you have to know how many heddles on each shaft are inside that range and move that count to the larger side.  You can do that by inspecting the threading draft again.

Hope that helps,

Jeff Anderson

cyberbarn

Hi Jeff,

Yes, that's it!  The supports are in the way.  The loom can be dismantled partially but the metal supports can only be dismantled from the levers, not from the heddle bars, so heddles can be moved, but not after they are threaded I don't think.  They would have to slide 6 inches along the bar which would put a lot of strain on the warp especially if there was a full width warp.  But not having the original manual (I would love to find someone who does) I don't know, maybe that is what they intended? 

What you say in your last paragraph makes sense. I am not an engineer (married one, gave birth to a potention one) but I am a scientist so I will have to do some calculating and see how I go.  Thanks for the help. 

jander14indoor (not verified)

As to one side, don't put strain on the warp until they are aligned!  When I'm warping (and I'm a near beginner) I regularly move the heddles all over the place as needed to gain access while threading.

Release center posts, if you can figure out how.  As Sara said, there is probably a fairly easy way.  On my baby wolf they are just hooked, not hard to free when you know the trick, but hard if you don't. You can't free the bar from the hook if the heddles are near it, not enough play.  Slide heddles to either side, see if you can unhook the bar.

Thread. 

Sley roughly centered (math helps there again, 100 threads, 10 epi 10 inches in read, find center of read, measure 5 inches or 50 dents on 10 dpi reed to right or left and start sleying).  You can adjust reed centering after tensioning. 

Tug on warp gently trying to align to center, treadle the loom.  The actions of harnesses going up and down automagically aligns the heddles.  

Increase tension with your hands, centering the warp.  Heddles will move, though they may need coaxing past the center point.

Re-attach hooks.  Tie onto cloth beam, tension.  Treadle again to align heddles.  See if things are 'good enough'.  Look for threads that take a sharp bend as they go through the reed, likely to wear and break.  If it is because heddle is on the wrong side of the center, loosen tension, unhook and move that heddle.  Or maybe just move the reed a little off center.  A little off isn't going to hurt as long as the path is straight.

And all that's why I like to pre-calculate.  Well, that and the fact that I'm a geeky engineer who overanalyzes things because I think its fun.

Jeff Anderson

Livonia, MI

Submitted by cyberbarn on