Well, I am close to the end of a vest material I am making and what I was afraid was going to happen, has. It looks like my warp is going to be too short. I thought it probably would be as I had a mess trying to dress the loom and wasted probably about 2 yards of warp. I know about taking the end of the warp and looping the knots through a cord so that I can use it up to the end, but am afraid I will still be about a yard short. Is there any way to just tie on to the existing warp so that I can finish? I am new to weaving so if there is, please use terms a dummy can understand......lol

Comments

Sara von Tresckow

If you have enough to make part of the vest with what you have, just relax, weave to the end of this warp and make a new one for the rest of your cloth.

Probably making a new warp chain with the same number of ends and tying on would make the most sense.

You have two choices - you can cut off your present warp in front of the reed, and from the cross in the lease sticks of your new warp, tie the threads in order to the existing warp. Be careful not to cross threads or things will tangle. Then beam the new warp pulling it onto the warp beam and you have your threading and reed the same as last time and can complete your project.

You can also cut the old warp such that you make a little overhand knot in groups of threads in front of the reed and do the same leaving nice tails to tieon with in back of the shafts. You then beam your warp through a raddle and when it is on the back beam you tie your knots in order, pull the neew warp forward and tie on on the breast beam.

There is no good way to piece a warp so that you can, say, cut a vest front out of the patched warps.

 

Jane Greer

could I cut the warp behind the heddles and tie on there so that I don't have to retread the heddles? 

Sara von Tresckow

Either way you do not need to rethread the loom. If you tie on in the front, you have merely cut the ends in front of the reed, leaving the warp firmly tied to the back tieon stick attached to the warp beam.

Jane Greer

or better yet, could I cord the existing warp so that I can work it up to the heddles and then tie on there? The warp thread is chenille so the know would be small enough to go through the heddles, i think. I just didn't want to do a whole new warp that would only be 2 yards long. 

 

Sara von Tresckow

Your level of experience is such that any experiments at this point might be more trouble than they could be worth.

Do one of the two methods - both tried and true, and massage the knots through the heddle eyes delicately by hand - heddle by heddle if need be - and it should work.

You've had enough issues to this point - you need to learn to do the "long cut" normal way of warping a loom and get proficient at it before thinking up "brilliant" new methods. Weaving has been going on for thousands of years, there is no need to reinvent the wheel.

Jane Greer

oh I agree!!! I just want to get beyond this one so that I can try out all the lessons learned from the mistakes I have made!!! Thank you!!!

Jane Greer

I must of read your solutions wrong, because either way you said to do it looked like I would have to rethread the loom. If I cut the warp in front of the reed, I would have to rethread the new warp and resley the reed in order to tie up to the old cut warp? Am I missing something?

Sara von Tresckow

If your warp is not disconnected behind the heddles when you finish weaving, everything is threaded.

Now you cut off five to seven inches in front of the reed (when the tieon stick reaches the back of the shafts).

Then you take your new warp, with lease sticks and cross (this cross is what keeps your warp ends in order). Secure the lease sticks near the breast beam where you can cut the loop and extract single threads.

Then you make an overhand knot for each warp thread from one side to the other - try to make the knots even, but the slight differences will even out when you come to the other end.

When all threads are connected in the front, you work the knots through the heddle eyes, even the warp chain so it can be held under tension, and crank the warp beam handle until the new warp is in place and then tie on at the breast beam once again.

This cannot be terribly difficult to envision.

You should really get a good comprehensive book on weaving like Lundell's "Big Book of Weaving" or the "Ashford Book of 4-Shaft Weaving" by Anne Field - you'd be able to picture these actions much better.

Nassajah (not verified)

you're explanation is perfect.  I've copied it for future reference.  Knew that there must be a way to add on to an existing warp, something that I wanted to do with a very finicky 20/2 cotton warp, but no one that I knew had a clue on how to do it.  Since they were more experienced weavers than I, I thought they knew best.  Well, now I know how to do it.

Thank you! 

Jane Greer

Got it! Thank you and I already have those books plus many more. I couldn't find anything about this in any of those books, but thanks! Forgive my ignorance

Submitted by Jane Greer on