I'm a new-ish weaver and have a question suitable for an amateur like me. I recently bought a new-to-me Louet Spring 110, which I adore. For those not familiar with this loom, it is quite lightweight, especially for its size (approx 100 lbs for 43" weaving width). I understand that this is not a rug loom, which is fine with me, and for most items I like to weave (scarves, dinner napkins, etc), it is terrific. However, I put on a closely-set warp of 8/2 unmercerized cotton to make waffle weave towels, and I can't get the ppi even close to the epi. I would chalk it up to my not beating hard enough as I am not a super-strong person, but when I beat harder, the whole loom shudders, shakes and walks (sometimes even jumping a little!) . I worry that I'm going to damage the loom! I don't mind having rectangular waffles in my waffle-weave - I actually think it looks interesting - but I want to make sure that I am not using terrible technique, and of course I don't want to damage my beautiful loom. Are there any techniques or tricks for beating tightly other than brute force? Should I be more gentle with this loom? Should I weigh the loom down with sandbags or something similar, or will that stress the loom even more? Should I simply use a looser sett with this yarn? This seems like a dumb question, but I haven't been able to figure it out on my own or find the answer in books or other resource materials. Thanks so much in advance for sharing your collective wisdom.

Comments

SallyE (not verified)

We need more information to help you.   What size reed (dents per inch) are you using?   How did you sley it (threads per dent)?

Sampling always helps.   You can do that at the begninning of the warp.  Sometimes, you have to used a different size thread for the weft to get the results you want.

 

jlread (not verified)

maybe closely set is too close.....or you are trying to squeeze too many picks in. I have a waffle weave on my loom now and it's 24 epi....I actually don't count the picks but make sure the weft is snug [I don't beat hard].....there is no way I could do 24 ppi....it does look rectangular....but it all 'comes out in the wash'...literally!....Don't over think this~

Joanne Hall

Hi Weaverwendy,

When you plan projects for small looms and jack looms, you frequently need to use a more open sett (fewer ends per inch).

So, if you follow a project from a Swedish publication, for instance, you need to plan on fewer ends per inch on your loom.  Swedish weavers use larger looms with counterbalance or countermarch tie-ups and these looms will give you a tighter weave.  Setts published in Handwoven can sometimes already have fewer ends per inch, as they write for weavers with a variety of looms. 

Sampling is good.  But also remember that the wider your warp, the harder it is to beat tightly, especially on your small loom.

Joanne

Weaverwendy

Thank you all so much for your speedy advice! To answer the questions that were asked or implied, my loom is a countermarche. The sett is 30 epi, sleyed 3 ends per dent in a 10-dent reed. As I thought more about what's bothering me, I realized that I'm much more concerned about the shuddering loom and less about whether or not I sett the warp too closely (I was aware when I did it that I probably was, but that part was an intentional experiment). I realized that the loom is shaking when I beat on basically every warp, and I'm trying to figure out whether this is "normal" or whether I could damage it, or if It's in need of some kind of adjustment or repair. I tightened all of the screws and bolts, and the loom is in alignment as far as I can tell. I'm not having other problems - for example, crooked wind-ons or wonky tension; the shed is fantastic and big as the whole outdoors (slight exaggeration, but you get the idea). Is this loom's sweet spot limited to very delicate-type weaving? Jlread, it was reassuring to hear that you are getting less than 24 ppi with a sett of 24 epi - it makes me think that 30 epi/30 ppi just won't work with this yarn in this pattern. I am going to re-think the shape of what I can reasonably get with my sett when deciding on the tie-up and treadling pattern for the remaining towels in the project. Joanne, thank you for the info that a tight beat is harder on a wider warp. It makes perfect sense, but I hadn't thought about it, and it could explain a lot! Thanks again!!!

ReedGuy

Are you using 5 treadles and 4 shafts? 4 treadles won't square up waffle. And weave structure can effect epi/ppi ratios as often as yarn size. Some yarns the same size will simply pack tighter than others (wool vs cotton) as well. Sampling is the best approach.

Sara von Tresckow

8/2 cotton is normally sett at around 20 epi for plain weave and 24 for twill. Your 30 epi is truly a bit close even for waffle weave,

Also, truly "square" or evenweave cloth is more suitable for cross stitching than for other uses. Commercial fabric usually has a slight warp dominance to give fabric the "grain" refererred to in sewing patterns.

rosearbor (not verified)

I've seen people weight the bottom of their looms with sandbags and putting them on rubber mats to minimize the walking you are describing.  But I wonder if the moving breast beam that is a feature of the Spring is contributing to what you think of as shaking?  I'm sorry, I've never woven on one of these, so cant say if it's normal behavior...

ReedGuy

Measure the fabric you are weaving with the ruler and see how many weft shots per inch, adjust sett from ppi.

ReedGuy

I'm going to be weaving some open woven scrim with nat. linen. So my plan is to insert a 1/8" brass rod in with the weft. Using two rods remove the front one (closer to me) each time as I advance in the weave. Using 8 dent reed,  one end per dent. Should make consistant spacing I would hope. I think I will use a light myst of hair spray on it as I weave sections to reduce slippage when handling the cloth once off the loom. It won't be gobbed on like mousse. :D

jlread (not verified)

Another thought...simply re-sley for a wider project...then proceed using less picks...when you wet finish, it will likely square up due to waffle structure and cotton shrinkage...all is not lost

BWeaves

Another thought on the ppi.

Are you measuring with the tension on or off?   

When you release the tension the fabric will be less vertical, and the waffles may square up.  After washing, they may square up even more.

Sample, sample, sample.

Cleo

I have a Louet Spring loom also. Jane Stafford has some excellent instructions and hints for using this loom on her website. I had a problem squaring an overshot pattern and she told me to take the beater to the fell line and push then change the shed. Since I have been doing this I realized it was not necessary to use a lot of force to beat with. It really improved my weaving also. Every loom is different. The suggestions on sett were also excellent. She is wonderful about answering questions directly also. Hope this helps. Cleo
Submitted by Weaverwendy on