I am on shawl two of a series.  The weft for the first was 10/2 Tencel, which went very well.  The weft for #2 is single ply silk, about the same weight as the 10/2.  Althogh the silk doesn't seem to be any slicker than the Tencel, my pirns are falling apart. The underlayers are coming out and formng loops that the thread end catches on.  I have had to stop seveal times and unwrap and rewind the pirn.  To say that this is tedious is wildly understated.  Has anyone seen anything like this?  I have used this shuttle and the pirns for it (it's a Leclerc fly shuttle with wooden pirns) for a long time without anything like this happening.  I don't want to change shuttles because I would have to remove the fly shuttle beater, which is a pain.  I also want to use the fly shuttle for this fairly fine fabric.

Comments

SallyE (not verified)

Ya, I've had that problem, today in fact - about an hour ago!

My problem seemed to be caused by two things:  (1) winding the pirn too close to the tip, and (2) winding the pirn too loosely.   The thread being fed onto the row for the current pick seems to drag some other threads with it, mostly from near the end of the pirn.

So if you are up for an experiment, take the offending pirn and rewind it onto a new pirn, but wind it tighter and stay a good distance away from the end - and inch or so.

I don't know if this will work in your case, but it seems to work for me.

 

 

sally orgren

If so, I am then wondering if you need some kind of slight drag on the thread. I have heard folks discuss using shuttles with a bit of fur to slow down the thead at the end of the pass through the shed.

 

 

laurafry

As stated previously, pirns need to be wound tightly.  Try again with more tension on the yarn as you wind.  Also keep the 'advances' short - no more than about 1.5 inches.  I have a video clip on You Tube

http://tinyurl.cc/h1nfyw

showing how I do it.

cheers,

Laura

sandra.eberhar…

These were wound as tightly as I usually wind pirns, which is pretty tight.  I've never had this happen before, and I've woven a lot of different yarns with it.  This shuttle has a tensionind device in it, so it has drag on it.  These are acting like what Sally mentioned will happen if you wind too close to the end, but this is happening in the middle of the pirn.

SallyE (not verified)

Is the pirin sitting level in the shuttle?   For some reason, the outgoing thread is draging other threads with it.   My Schacht shuttles have a little screw that levels the pirin, but I don't know about the Leclerc ones.

 

debmcclintock

did you have a drop in humidity in your studio? silk will pick up static and act stupid when the humidity drops, try light mist of water....very light

ReedGuy

Did you build up the yarn like a cone from the attachment end and not travel with the yarn the length of the pirn?. Don't advance the yarn to much before that cone is build up like Laura suggested. I know you know how to wind pirns. Maybe a little myst water will work as suggested, apply before installing the pirn. Are the pirns ribbed?

sandra.eberhar…

I think the moisture item might be it.  I wound these pirns when it was snowing, (it's been snowing constantly here) usually snowing really hard; the equivalent of a big rainstorm.  Now it's clear and dry.  My studio is in the barn loft, and although it's insulated and fairly well sealed, it is not climate controled, and not heated when I'm not working.  I'm going to rewind them, paying special attention to tension, wind skinnier pirns, and mist them before using.  Thanks!  I never thought humidity could make that much difference.  This is going into the Heart Throb pattern from Thrill Twills. I'm using 2/18 black wool and assorted wefts.  I have bamboo and silk noil planned as well as this silk.  It's coming well, but making me wish for a dobby.

laurafry

It doesn't take much of a shift in humidity to make a difference. :(. Hope re winding the pions does the trick. The other fibre really susceptible to humidity changes is linen. Our winters can be quite dry so I run a humidifier when working with either of those fibes when it's dry. Cheers Laura

Joanne Hall

You should also try winding so that the yarn ends up sitting diagonally on the pirn, not in rounds like a spool of thread.  To do that, the hand holding the thread needs to move back and forth faster.

Joanne

Submitted by sandra.eberhar… on