Greetings,

I don’t know if anyone can answer this. I have several people in the UK who have bought my book - Building A 4-Shaft PVC Loom. But, they are not able to find the Schedule 40 PVC Pipe we have here in the US.

A friend of mine sent me a link to the Cole Parmer website. http://www.coleparmer.co.uk/catalog/product_index.asp?cls... But, the price is a full 13 times what we pay in the US. A 9 foot length of 1 1/4” PVC pipe costs $10.50 in the US. In England, it costs £84.00. That’s $132.00 in US dollars.

They say it’s due to shipping costs, plus duty taxes. image title image title

So, I was wondering if anyone knows what kind of PVC pipe is sold in England.

Comments

artag

Hardware is often expensive and comes in restricted ranges in the UK. The excellent little shops we used to have died out when the big stores came along - and now we have to buy DIY kits or go to trade specialists. I envy the US hardware stores. Don't use the big ones - you can't afford to lose the little guys.

Plumbing isn't too bad, though. There are a few types of pipe available, usually sold (at least in retail) by usage rather than specification. They split broadly into high pressure supply pipe (which is slightly flexible) and waste pipe, which is larger diameter and stiffer. There are a few types available in each - I think there are high temperature variants, and some that's more suitable for outdoor drainage.

Here's a selection from one of the big retailers. It doesn't seem to cover all the options, but I can check out some of the details if you like.

http://www.wickes.co.uk/pipe+waste/waste-pipe/icat/wpipe/

 

WeaverDave (not verified)

I'll pass that along.

artag

Dave, the one thing I'd be concerned about is the bendiness of waste pipe. I do agree that manufacturers someimes overemphasise the furniture aspects of their looms, but shouldn't beams stay fairly straight under tension ? I rather like the loom sold for the TC-1 jacquard myself, which is made out of 50mm aluminium extrusion.

Maybe that schedule 40 pipe is stiffer than the typical pipe we have here, or maybe you have a clever method of strengthening it (I haven't bought your book yet, though I'm rather tempted).

Are there any tests you can suggest to make sure it's up the job ? For instance, if I take a 4' pipe and put a few pounds in the middle, how far does it bend ?

 

WeaverDave (not verified)

The pipe recommended here in the States is the schedule 40.  But it is 1 1/4 inches in diameter.  The rollers are 1 1/2 inches in diameter.  The large diameter of the pipe makes it more rigid.  (This is the same design principle used by the bicycle company Cannondale in their bike frames.)  Plus the design is for a loom that can weave 24 inches wide.  That's just a little over 2 feet wide.  The combination of width and tube diameter creates a very stiff loom.

I not sure if there is an experiment you could do to test other types of PVC pipe.  With the sizes I specified above, there is hardly any bending at weaving tensions.  But again - that's with PVC pipes that are about 28 inches long. 

artag

You're right - in a short length, it doesn't bend much. 

I've found a length of 32mm (1 1/14") pipe in the garage. It's about 2mm (3/32") wall thickness but it's not PVC, it's the high temperature stuff and is marked for use in pushfit systems rather than solvent weld. But a 28" length deflects only about 1/4" if I load it with about 10lbs. PVC probably isn't a lot different - maybe a little stiffer, if anything, because it's harder. If it turned out to be a problem, you could always push a length of timber or steel tube down the pipe to stiffen it up!

Here's another supplier that's quite common here. It's a useful link as it mentions the actual manufacturer (FloPlast) and information about the appropriate standards can be found on their website. Of course, we do have standards for these things - we just don't call them Schedule 40.

http://www.screwfix.com/c/heating-plumbing/grey-solvent-weld-waste/cat8…

http://www.floplast.co.uk/about_us.asp

And there are cheaper alternatives, as Paul points out. It's worth shopping around.

 

Submitted by Anonymous (not verified) on