OK, so it's fess up time.  I use floating selvedges all the time, but I don't set them up correctly and am tired of paying for it.  I just tie them with the other warps and try to make them tighter, and sometimes that works, but most of the time I have to make sure before each beat that the edges will be OK.

I know you're supposed to hang them off the back beam with weights, but my loom is against a wall, so wouldn't I have to pull it out to reposition the weight after every advance or two? And what do you do with the yarn that is yet to be weighted, so it doesn't just sit on the floor and get tangled?

I really need to start doing this correctly.  It really slows down my weaving.

Thanks,

Karen

Comments

Sara von Tresckow

Depends on your loom. I use only countermarche looms and just beam any floating selvedge with the rest of the warp. Because the warp is pulled both up and down, t he floating thread sits clearly in the middle with no fiddling necessary.

On a jack loom with a good "dip" they would also sort of sit in the middle - until you crank up the tension, then they'd disappear.

On a rising shed loom with no dip, Heaven help - they wouldn't stand out much at all.

You could try to achieve the extra tension  you seem to need by putting blocks on the back beam to raise the floaters and give them what you need.

laurafry

You could just not use floating selvedges at all.  I don't - they slow me down too much.  :)

Cheers,

Laura

Cynthia

Laura -- but what about a twill where the edge threads don't catch?  Do you thread a special selvedge?  I'm weaving an undulating twill right now & every time I reverse treadling direction the edges get so wonky that I ended up adding floating selvedges.

 

Karen -- I wind my floating selvedge threads on perm rollers, then put fishing weights inside.  You can let them dangle almost to the floor, so you don't have to fiddle with them very often, and I would think you could reach the rollers from the side of the loom without moving it.  I like the perm rollers because of the little stretchy band that is meant to hold hair on; it holds onto yarn very nicely.  Film canisters work fine, too, and the weights don't have to be as small, but they are getting hard to find.

TinaHilton (not verified)

What I do sometimes is to beam them with the rest of the warp, but tie they looser than the others.  Then I add a weight to the thread back by the warp beam.  I use something that just hooks over the thread (like an S hook) so it's always just dangling there at the bottom.  You never have to move the weight this way.  I do take it off if I'm not going to be weaving for several hours.  I don't know if it's really necessary to do that though. 


villageweaver (not verified)

Twill selvedge threads not catching:

if you start a twill project draft, and you are not catching your selvedge threads right away, unweave what you've done. Start on the pattern pic 2nd, 3rd, or 4th and try again. if still not catching, unweave and start with pattern pic 2 and throw the shuttle from the opposite side you had been throwing from. with a little moving that first pic to another, you will pic up every selvedge thread. it really works.

takes a little bit of figuring in the beginning, but you will not need a floater for twill AGAIN!

hope this is clear -

Sara von Tresckow

 And zigzag or goose eye twill? On thread 10/2 cotton sized or larger?

That is my one exception because you get the edges bound in only one direction - as soon as you have completed the zig, the zag leaves loops at one side. Basketweave at the edge would be the other solution.

Loominaria (not verified)

 I do the same thing when an edge warp or two get loose on my rigid heddle loom from too much clumsy thumping from a poorly aimed shuttle (or any warps that were beamed significantly looser than their neighbors). I have used very large hardware washers and kumihimo tama (weighted bobbins) for the weights. Tablet weavers also frequently use weighted warps so they can periodically untwist the selvedge warps that are being turned in one direction.

Kurt

Cynthia

But what if you reverse treadling direction?  I find that I can catch the edge of most twills as long as I'm treadling in one direction, but one that zigs & zags needs a floating selvedge.

Lizbuppers (not verified)

Do you hang the wwight between the warp beam and the shafts?  If I do that, it just makes the selvedges hang lower than everything else, so they won't be floating.

TinaHilton (not verified)

I have it hanging back under the warp beam. 


Loominaria (not verified)

Weights hang on the warps at the bottom of the warp beam. The weights then just slide along the threads under the beam as you advance the warps.

Kurt

Lizbuppers (not verified)

Thanks, I'll give it a try!

Submitted by Anonymous (not verified) on