I am trying to contact Dale at J made looms, and I'm not sure if the phone number I have is correct. I also tried an old aol.com email address I dug up from the internet, and it no longer works. Does anyone have his contact info? Thanks, Wendy
Thanks for the address....I spoke to him less than a year ago and he was great. I haven't had luck with the phone number (it rings but no one picks up), and I live overseas so I was hoping to find an email address for him. I'll keep trying the phone, and I'll send off a letter. In the meantime, if anyone has his email, I'd appreciate it!
I sent him a letter about a month ago, and haven't heard anything back (I'm overseas, so it might take awhile, but it sure should have arrived by now). Does anyone have his email and/or more current information? Thanks, Wendy
Looking for anyone that might be able to share any paperwork for the 16 harness J-made loom. Especially curious about assembly instructions and necessary hardware. Thanks!
Looking for anyone that might be able to share any paperwork for the 16 harness J-made loom. Especially curious about assembly instructions and necessary hardware. Thanks!
i just purchased a J made 12 harness convertible table loom with treadles. My husband cannot figure out how to assemble the strings and cords to attach the harnesses to the treadles. They are all there I believe, but the diagram we have is not 3 dimensional. Can anyone help?
i just purchased a J made 12 harness convertible table loom with treadles. My husband cannot figure out how to assemble the strings and cords to attach the harnesses to the treadles. They are all there I believe, but the diagram we have is not 3 dimensional. Can anyone help?
Does any one have a picture of a J-made Table loom, or instructions for assembly? It is currently on a floor loom conversion and I would like to restore it to a table loom.
Comments
Dale at J Made Looms
Try this:
Dale Johnston
19290 S. Badger Dr.
Oregon City, OR 97045-7660
503-631-3975
GREAT guy!
Dale
Thanks for the address....I spoke to him less than a year ago and he was great. I haven't had luck with the phone number (it rings but no one picks up), and I live overseas so I was hoping to find an email address for him. I'll keep trying the phone, and I'll send off a letter. In the meantime, if anyone has his email, I'd appreciate it!
Still no word...
I sent him a letter about a month ago, and haven't heard anything back (I'm overseas, so it might take awhile, but it sure should have arrived by now). Does anyone have his email and/or more current information?
Thanks,
Wendy
J-Made loom
Looking for anyone that might be able to share any paperwork for the 16 harness J-made loom. Especially curious about assembly instructions and necessary hardware. Thanks!
J-Made loom
Looking for anyone that might be able to share any paperwork for the 16 harness J-made loom. Especially curious about assembly instructions and necessary hardware. Thanks!
J-made loom
I have a J-made 16 harness loom! I'll PM you.
J-made loom help!
i just purchased a J made 12 harness convertible table loom with treadles. My husband cannot figure out how to assemble the strings and cords to attach the harnesses to the treadles. They are all there I believe, but the diagram we have is not 3 dimensional. Can anyone help?
J-made loom help!
i just purchased a J made 12 harness convertible table loom with treadles. My husband cannot figure out how to assemble the strings and cords to attach the harnesses to the treadles. They are all there I believe, but the diagram we have is not 3 dimensional. Can anyone help?
12 harness J made
Kathy,
I believe Clemes and Clemes are making these again. So maybe they can help too. I have an old Dale Johnson made 12 shaft that sounds similar to yours.
J Made
I think that Clemes are only making the smaller table looms and treadle stand, not the large floor looms.
J-Made Table loom
Does any one have a picture of a J-made Table loom, or instructions for assembly? It is currently on a floor loom conversion and I would like to restore it to a table loom.