Hi,

I have been searching an answer to my shuttle problems all over the net but found no cues.

I have a thin wool scarf on my loom. The loom is Scandinavian (Toika) countermarche loom. The warp is tripled (yes that´s right) thin lambswool and alpaca and 5 ends per 1cm. The weave is barleycorn/broken twill. I use small boat shuttle with upward pointed ends. The sheds are clean and tension as tight I dare to pull with delicate yarns. I use tripled weft as well. I know by this far this project is made up of ´not-to-dos' but everything looks neat.

The problem occurs with two sheds (2 and 4) when I am throwing shuttle from the right to left. I have analyzed my style of weaving but I seem to make pretty much the same gestures on both sides and sheds 1 and 3 work fine. 

I have tried lowering the reed but the bottom shed is good to begin with. I have put extra care to bobbin winding. I beat (or put the weft in place) when switching sheds so I can clear the shed for next shuttle round.

Am I to accept that my shuttle will stick until the end of this warp? Usually it catches near the middle of the warp but there´s no mistake or gap because of cords or heddles. I thought I would ask advice before I surrender with this project. I know here´s so much talent and experience that could point me to the right direction.

Also one other question has been troubling me. What kind of boat shuttle goes well with my kind of loom? I have only used that one because I have never seen anything else for sale in my corner of the world. For instance swedish-type boat shuttles are extinct in Finland even though we´re close neighbours. I am interested in a little bit longer shuttle (mine is 10.5") and would love to hear recommendations for one.

Thank you all for your advice and have a good day

Niina

 

 

 

Comments

sandra.eberhar…

I have read your post, but I can't figure out what the shuttle is doing.  You say it is sticking, but what exactly is happening?

niina

Well the shuttle catches couple of bottom shed threads when going in from the right (sheds 2 & 4). The shed is clean and all threads the same height but perhaps it all comes down to uneven tension with warp, although I can´t notice it. I have been weaving bits throughout the day and can´t pinpoint the cause. The warp is usable, it just takes forever to guide the shuttle with these two sheds. Also I suspect the shuttle because of the upward points to behave a little wobbly (it´s very light shuttle), but can´t compare because I only have that kind of shuttles.

sandra.eberhar…

Well, I can think of a couple of things to try.  You say that the problem is on sheds 2 and 4.  Try throwing the shuttle the opposite direction for 2 and 4.  If it still catches, it's the shed and not your motion.  It sounds to me as if your sheds are not as clean as you think they are.  You have said that using several threads of warp and weft together are bad things to do, but I often do this without any problems.  Is the warp sticking together?  You may need a warp dressing or increase the tension.  You haven't mentioned any warp threads breaking, and you haven't said what size your warp and weft threads are.  Your warp may be capable of taking more tension than you think.  If it turns out that it is not your motion, but the warp itself, I would increase tension and use a warp dressing.  I have used an oil used to detange horse hair that works well. 

sandra.eberhar…

Also, you have said that the boat shuttle you have is all that is available to you, but you have a Toika loom, and they make a variety of shuttles.  Have you tried contacting your Toika dealer?

Sara von Tresckow

Wobbly shuttles can be contributing to your issues. By tripling the threads, you have a shed floor that is perhaps not quite as smooth as with single threads.

When I have a project like this, as a drawloom weaver, I gravitate toward my damask shuttles. What are they? They are boat shuttles that are longer and flatter than the usual curved end Swedish shuttles (and those are an improvement over the ends that tip  up). You "lay" the long flat shuttle in the shed and push with your finger and they slide across. Having the longer shuttle with a bit of mass stabilizes its run across the warp. Short, light shuttles are cute, but not as functional as the longer, heavier ones.

Peg R

Sara, I occasionally hav the same rouble. You mentio damask shuttles. Where  can you buy those?

Sara von Tresckow

We carry several versions. I'll send you a PM with sizes we currently have in stock.

Submitted by niina on