Hello all!

I have an old Dick Blick 4 harness table loom.  The lever catch is not working properly and will not lock a few of the shafts in place. It looks as though the metal has been shaven off the lever catch with excessive wear n tear. Does anyone know where to find replacement parts for this loom? or is just time to invest in a new loom? Thanks for your help!

Lever Catch view 1

Lever Catch view 2

Comments

sequel (not verified)

Are you speaking of the hole where the spring connects?  If the metal is wearing away there, you may be able to find a steel washer the right size to reinforce the hole.

Probably no new parts are available, but you may find used "parts" looms somewhere.

3lue3onnet

The whole metal catch needs to be replaced; the part labeled "C". The problem is in the grooves where the levers are suppose to lock and sit. The metal has been worn down and the levers no longer lock into the grooves. 

bjr1957

Hello All,

Just yesterday I finished putting the finishing touches on an old loom I got for $350.00.  It had 4 harnesses and 6 treadles.  It had room for 4 more harnesses and 4 more treadles.  I had friends of mine make the additonal parts and got them installed yesterday.  Took almost a year of work but it is all done.

Now I need heddle bar J hooks and 3/8 inch heddle bars for the additonal harnessess.  Anyone know where these can be found?  I live in Shelton CT

Thanks.

ShawnC

I have one similar to this (old Structo). I don't think you need a whole new piece. Mine is quite worn and functions well. The spring was replaced at some point, though, as it wasn't working/holding shafts up. Try pushing down one lever and watch what happens (and feel the tension-should be quite strong).

bjr1957

Hi Shawn!

Thank you for the reply!  I am not sure what you mean by "The spring".  There are no springs on this old loom.  In the pic I put up you can see the new shafts have no J hooks to hold the heddle bars and...of course...no bars to hold new heddles. 

The J hooks (8 needed) hold the bars (8 needed) in place so I am not sure what you mean by "springs".

Thanks!

Barb R.

ShawnC

Sorry, Barb. I was speaking to the original post!!

ShawnC

 (posted this in the wrong place-sorry) I have one similar to this (old Structo). I don't think you need a whole new piece. Mine is quite worn and functions well. The spring was replaced at some point, though, as it wasn't working/holding shafts up. Try pushing down one lever and watch what happens (and feel the tension-should be quite strong).

3lue3onnet

Thanks for your reply Shawn!

Shaft/Lever 1 works just fine. Shafts/Levers 2-4 will not lock in place.

I have tried adjusting the tension on my warp too.

There were metal shavings under my loom from this part. I'm pretty sure it needs replacement now. I guess I will have to keep my eye out for looms to frankenstein together.

ShawnC

Hmmm. It might be worth checking the spring. If it is weak, it won't rock the part (C) back far enough for the shaft thing (little roundish piece) to lock. If this is the issue, it's an easy/cheap fix. Whoever replaced mine also moved the hole further back so that it's a heavier spring with more leverage. I imagine this issue would also cause wear on part C, as the shafts try to grab anyway.

oldhausfibers

If you can't find parts on an Online Site (try eBay 1st), you may have to have a local machinist/welding shop take a look at it. They can look at the piece see how it could be built up, rebuilt, and give you an estimate.  Worn metal parts do happen, and on occasion need some touching up.  If you can remove the part, take 6 photos of it (all 6 views) & tell / show where the worn part is, I'd probably be able to give you suggestions too.  

Does a magnet stick to it?Suspend it from a string, tap it, does it plink, or ring? 

 That would get me started :) 

Good Luck! 

JLH

Submitted by 3lue3onnet on