I've heard of people beaming shorter lengths of warp on the outside sections so they can weave narrow items and wider items without having to completely rewarp, rethread, and resley.   I've also heard that you need to weave the narrow piece so that you don't have tension problems due to the outer sections having less yarn.   But how do you know when it's time to thread and use the outer sections?  I can't imagine coming close to having all the sections run out of yarn at the same time. 

Any opinions or suggestions would be greatly appreciated.

Comments

tien (not verified)

I'm having a hard time visualizing what you're talking about.  Are you talking about weaving three separate items on the same loom at once? so, for example, three separate scarves, woven with separate shuttles and separate wefts?

That just doesn't seem like a good idea to me.  You'd be practically guaranteed to get tension problems in one or more of the items due to differing take-up.  And why do it?  It's a lot faster to be weaving one warp with a single shuttle than be constantly picking up and putting down shuttles to weave three-at-once.

Or did I just misunderstand what you were asking?

TinaHilton (not verified)

I didn't explain it very well.  Let's say I want to weave towels 22" wide, but also want to weave runners 14" wide on the same warp.  If I wanted to use 10 yards of warp on placemats and 10 yards on runners, and I have 2" sections, I'd have 2 sections of 10 yards each, 7 sections of 20 yards each, and 2 more sections of 10 yards each.  Initially, only thread the 7 sections in the center, weave the 14" wide runners until 10 yards have been used, then thread the other sections and weave the rest as 22" wide towels.  Obviously, I'd have to cut off the placemats and tie the warp to the cloth beam again.

I did this once on a very short rug warp, but wove the the wider rug first till the outside warp ran out, then cut those ends off and wove the narrow rug until that warp ended.  Later I read I should have done narrow first, then wide so that the amount of warp on the beams was the same in each section being used.  Since it was a short warp, it didn't make any difference.  But now I want to try it on my AVL with a longer warp and so I want to do it the "right" way.  But I don't know if there's a simple way to know when I've used up the amount of warp for the narrow item so I don't have too much waste. 

Did I make this any clearer?

laurafry

It's clear, but personally I think it would be awkward to thread the shorter sections after the longer sections are already threaded.  Sounds like more work than just doing a second warp.  But then I can dress the loom quickly and threading isn't a big chore for me.  :)

When I did different widths, I wound the warp the entire width and length, then sacrificed some of the yarn (cut it narrower).  To me the expense of throwing away a few ounces of yarn was worth it when I really, truly had to do it.

Guess you need to try it once and see if you like doing it that way or not.

Cheers,

Laura

TinaHilton (not verified)

I wondered if it would be worth the hassle.  I'll have to try searching my emails again to see if I can find the weaver who said she/he did this quite often.

thelmaweaves

I've done something similar to what Laura has done.  I wove a bathroom rug, then wanted a towel to match.  Since I had enough warp left on the loom, I took about 6 inches from the center design section of the rug and (gasp!) cut it off. It was the first time I tried something like this.  It worked just fine. The design was such that the only place I could take warp off to make it narrower was in the center.  I figured if it didn't work out, I wasn't loosing much, since the remaining warp was just 26 inches. I did have a batch of heddles (about 144) with nothing on them in the center of my towel, but the reed straightened it all out.  It wove up just fine.

I think I would be afraid to use the shorter warp lengths, because of the tension problems that could develop.  I also use a dummy warp on my sectional beam allowing me to weave right up to the back heddles.

helgaundmichael (not verified)

you could mark threads: Let's say you have a smaller warp 10 yards long and a wider one only 8 yards. When winding on the smaller part mark one or tow threads after you had wind on 8 yards with color that would wash out later. When you reach the colored point in your weaving you will know that it is time to use the full width of your warp.

Guiding Myth (not verified)

 Hi,

I see I have come late to this discussion.  Perhaps Tina will see this anyway. 

I warp my 60" sectional loom this way occasionally - I put a longer warp in the center and shorter lengths on the sides.  I did not have tension problems - with cotton.  You have to plan it well and be willing to put up with some waste (unless you plan it perfectly which I never do).

There are at least two ways you can tell when it's time to thread the shorter sections after weaving the center longer section.

1.  When the sections appear to be about equal in yarn depth (if you are using a thicker yarn this works better than a fine one).This method can result in more waste.

2.  Use a warp beam counter and after the required number of revolutions you can tie on the shorter warps.  for example:  if the center warp is 10 yards long and the shorter warps are 5 yards long and you have a 1 yard warp beam after 5 revolutions of weaving you would thread the shorter sections.  

Cut off what you have previously woven on the narrower warp and tie on to the cloth beam/apron/rod again when you add the shorter warp sections.  Also make sure your threading and denting continue the way you want it - you need to start from the center warp and thread out  to the edges .

I warped my 60" loom this way recently but have not started weaving it yet (hard to stay indoors in the summer).  My plan is to weave some narrower throws and baby blankets and then widen the warp to weave wider throws/blankets.  

Laura has a good point about it potentially being awkward to thread in the shorter sections.  It would depend on the loom I imagine.  As I recall, it was somewhat awkward - because you are threading backwards on one side - but the section was narrow about 12 inches and was done quickly.   This time I plan to change the treading for the whole warp when I add the new sections - go from a point threading to a straight draw.

It works for me so if you think you would like to try it do!  

Stephanie Stanley

 

 

 

Bonnie Datta (not verified)

My approach is to warp for the widest piece, and weave it first.  Then divide the warp for the anrrower piece, and whatever is left over can be woven as mug rugs, bands, etc.  That way I don't waste warp and I don't have tension problems and in the end I have some nice coordinating items.

Bonnie.

TinaHilton (not verified)

More good things to think about, and I appreciate them all.  I use a warping wheel (homemade, but modeled after the AVL one) to warp sectionally.  I don't know if it's worth the extra hassle or not.

Submitted by Anonymous (not verified) on