Hi I am a bit puzzled, why I cannot seem to get the counterbalace loom to stay straight... Can anybody help me identify this issue.

 

Ashleigh

Comments

ReedGuy

Are the cords from the horses tied correctly. I can't really tell from the calamity in the photo.

On one side of the loom, tie horse one so that one end in on shaft 1, the other shaft 2.....with the horse on the opposite side of the loom tie the ends in mirror fashion on the same two shafts. Then with horse 2 on the left, tie one end to 3 the other 4 and mirror the tie up with the other horse on the right.

Tipping shafts usually mean they are tied wrong.

warpweftweave (not verified)

HI Reedguy; is there any diagrams; Not sure what you mean. the first horse A the horse in the front is tie on 1 & 2 and on the opposite side it is tied identically the horse behind horse B is tied up 3 & 4 and that is identically that same the other side. 'Laura Fry' said - On the left they should be / and on the right \ ...

warpweftweave (not verified)

THink I understand now... the cord should be on the ouside not in on the inside...

sequel (not verified)

The warp will level out the horses and shafts.  Right now they are just dangling in space.  Traditionally, the tie-up happens after the warp is threaded and tensioned.  Just be sure to evenly spread the threaded and extra heddles on the heddle bars.  The tension on the warp should straighten the whole thing.  If you have a very narrow warp, there may still be some wackyness...

ReedGuy

Sequel makes a good point, the warp should be on first. Even on a countermarche the warp goes on first before the tie-ups. There should be harnass blocks in place as well when tying on the warp ends to the cloth beam. So horse tie up cords are all even. There are no shortcuts when doing many tasks on the loom. But if the cords are not mirrored 1-2 then 2-1, shafts will tip. They cannot be identical. It woud be impossible to ballance otherwise, since there may not be exact number of heddles on the shafts and not all pieces of wood weigh the same, even if they are the same dimensions.

'Big Book of Weaving' would be your friend. ;)

jander14indoor (not verified)

This is not an issue of uneven wood, heddles, or no warp.  I'm pretty sure from the picture you have the horses tied wrong.  The forces cannot balance, thus the tilted shafts.

Example, on the first shaft, the left horse is tied on the right side well away from the end of the shaft.  The right horse is tied on the right side too near the end of the shaft.  And vice versa for the second shaft.  There is no WAY it can balance and it looks exactly like the forces would have it look.

Back to the first shaft.  The left horse will have more load since it is tied closer to the center of the shaft than the right horse.  On that same left horse the second shaft is tied closer to the end and will have less load.  Of course the horse tilts.  This is true even if every thing were perfect (referring to comments above about wood).

Do like warpweftweave said.  The first shaft should have both inner ends of the horses tied to it, and the second both outer ends (or vice versa).  the wood and heddles will balance well enough then not to be cockeyed like you have now.

 

Jeff Anderson

Livonia, MI

ReedGuy

When doing uneven numbers of shafts, the amount of heddles on shaft to shaft does make a difference. If for instance doing 3 shafts and one shaft has a lot more than the other two, the horses share that heavier shaft when tied or the shed will be troublesome. This is demonstrated in 'Big Book of Weaving'. I know that others have been successful no really balancing this way, but it depends on how many more this heavier shaft has. A significant amount or just a few.

kerstinfroberg

of horse-tying:

Also emphasizing what others have said: there must be a warp if the shafts are to "behave". Good luck!

cottageweaver (not verified)

I learned that the horses should be centered over the 'quarter' mark along the shafts (in other words, halfway between the end of the shaft and the center of the shaft).  Kerstin's diagram shows them this way, but you might not have noticed it.  This works well for me when I set my looms up as CB.

loomyladi (not verified)

Hmmm...... the comment on a problem with a narrow warp resonates well with me.  It explains much! 

 

loomyladi (not verified)

Hmmm...... the comment on a problem with a narrow warp resonates well with me.  It explains much! 

 

Submitted by Anonymous (not verified) on