I am going to try a small double weave sample and while I understand how to do a double weave, when i figured out the dimensions I wanted and used the calculator on this site, I became thoroughly confused....lol. I am going to make the bottom layer one color, the top layer a different color, both with the same color weft. I was only going to do 36 inches in length and 10 inched in width as I thought I would do this on my table loom before going to the floor loom. The calculator is telling me the length is 1.6 yards with 120 ends. Now here is the question, do I warp 120 ends of each color or only 60 of each? My mind tells me 60 each, but something just doesn't seem right with that. But I can't picture it, can someone tell me what is right? I have spent 2 hours searching this but can't find anything about how to wind a warp for a double weave or how to calculate for one. 

Comments

Jane Greer

Oh, and I will be joining one side to make a double width. 

pammersw

Each half is ten inches wide, right,  for a total width of 20 inches when you're done? At 12 epi, you need 120 ends of each color (120 of one color for the top and 120 of the other color for the bottom). I haven't done a double wide yet, but I plan to someday.  :)

Jane Greer

but then that would mean I would have to have 240 heddles since one end per heddle. That would make it wider then, wouldn't it?  that's what confuses me. the sett is 10 but would actually be 20 through the reed.

kerstinfroberg

Yes, as you are weaving for double width...

As you are weaving two layers, the total ends/inch (or whatever measuring system you are working with) will be double the "normal". As in: if each layer is having 12 epi, *both* layers together on the loom/in the reed will total 24 epi.

Jane Greer

so you are saying it should be 120 ends per color? but if i am threading color 1 on shafts 1 and 3 and color b on shafts 2 and 4, if i add another 120 ends, then that will make it 20 inches wide instead of 10, won't it?

Or did I answer my own question, it may be 240 ends but since there will be 2 threads per dent in the reed, it will still only be 10 inches wide but two layers. is that right?

 

 

ReedGuy

Half of those 240 will rise to form an upper shed, thus 120 ends there. The other half will be lowered to make the bottom shed, this is the other 120 down there. You need to double the number of ends if you want a double wide cloth otherwise it won't be double wide. One shed opens at a time of course. You will be doing plain weave here, and you will want to group your upper layer on shafts 1 and 2 and your lower layer on 3 and 4. And the color is alternated in the warp, say green, then red, then green, then red..etc.

The highlighted red areas weave the layer indicated (shafts,treadles). This draft begins on the bottom layer: shaft 4, treadle 4. Then treadles 2,1,3... You will find that the green side is the bottom layer. The fold is from the left side. Open on the right.

ReedGuy

I typed out the explanation wrong, the bottom layer is green, both sides of it. The top is red both sides of it. You will need to alternate the weft colors as well to get a soild color on each layer. Weave with two shuttles, one with each color.

Jane Greer

i am starting with just one shuttle at this point so as not to confuse myself completely, but I did notice you did the alternate threading, do you find that is easier than the straight draw?

My original intent was to do this on my table loom, but now that I see how many heddles it will take, I have to rethink this....lol

ReedGuy

If you do a straight draw your layers will be bound and double thick instead of double wide.

Jane Greer

even if I connect on one side?

 

ReedGuy

To get two separate layers here and open on the right one shaft has to fall, and the other 3 must rise so they are pulled up into the upper layer out of the way. So your shed is now underneath the upper layer. Now your on the left where you want the fold and are going to go across the top layer now, so now one shaft on the top layer must rise and all the other shafts go below on the lower layer out of the way. Your shed is now on the top. So like before 3/4's of the threads are now opposite 1/4 of the threads. Your now on the open side where you began, but on the top layer. Now you have to return across that top layer and so the alternate threads are up now. Same number of threads up as down, but the top shed threads switch position so the opposite threads are now up. Now your at the fold again so you have to put 3/4's of the threads up out of the way and 1/4 down. Which is the opposite 1/4 from when you began. So now you went back across the bottom to the beginning. You have to make return trips across each weaving layer and whichever side you begin with the shuttle is your open side.

What your going to do with a straight draw is get stitched doublecloth.

Jane Greer

i thought if I only used one shuttle and a straight draw, and did tabby a of the top layer, tabby a of the bottom , tabby b of the bottom and then tabby a of the top it would close one side?

ReedGuy

Yes, but double the color (2 green,2 red) instead of alternate with single color. Threading alternates is easier to conceptualize.

danteen (not verified)

You can do a straight draw to get your double weave, you just can't use the same tie-up at Reed Guy showed.

Using straight draw with shaft 1 and 3 weaving top layer and 2 and 4 weaving the bottom layer, you could tie-up:

1   And throw right to left and weave the first pick of the top layer

1,2,3 throw left to right and weave the first pick of the bottom layer

1,3,4 throw right to left and weave the second pick of the bottom layer

3   throw left to right and weave the second pick of the top layer.

This progression of four picks will put your fold on the left side.

Teena Tuenge

 

ReedGuy

The Tie-up is fine Jane, just use your threadling sequence you wrote out with a straight draw from shaft 4,3,2, 1 (1 at the top), my treadle 1 is always on the right hand side. What Teena wrote out is exactly what you will be doing as you wrote moving the shafts she describes is exactly the way the original tie-up is written by me. I checked it in software before I replied. I'm right handed so I start on the right as treadle 1. Can be confusing depending on what a person assumes the other is using for convention. And I have books that name them one way and then another book names them in another direction. :) That is why a diagram (draft) can trump wrighting it out on paper. However, I do think you meant tabby b as your last pick on top

ReedGuy

The draft as you want it. Red as you can see are on the shafts for the top (shafts 1,2), greens below (shafts 3,4)

jander14indoor (not verified)

For what its worth. 

I did a couple of similarly dense warp projects on an pretty old LeClerc Medico table loom (a variation on the Dorothy), Rep Weave not Double Weave. 

To put it mildly I struggled throughout those projects getting a consistently good shed.  The warp strings were so close that it was a struggle sometimes getting the warp threads past each other as I changed sheds.  The harnesses that should have gone down caught on the upgoing harnesses (rising shed loom).  Had to apply WAY to much force for that light loom.

I don't know that all small table looms would have this problem, but as I also have a big countermarche floor loom I certainly wouldn't try a dense warp on that table loom again.

Jeff Anderson

Livonia, MI

ReedGuy

Yes, and on a rising shed loom the tie-up is the opposite of the sinking shed countermarche. The shed opening is not going to be as open on a rising shed loom. As you can see you have 3 opposing shafts against one on every treadle. It is going to be easier raising only one shaft, than three. But time will tell.

Jane Greer

maybe I need to move this to my floor loom?

 

ReedGuy

Your better off sampling on that floor loom if you have intensions of doing a 'for real' project on it anyway.

ReedGuy

That's what they pay me the big bucks for. :)

Submitted by Jane Greer on