I have a JL Hammett 4 shaft 4 treadle loom, I am a brand new weaver and  I have never set up anything but a cricket.. Hubby and I have spent the last 2 months tryng to get this loom set up corretly and we are about to give up..Please, please can someone helpmemake the adjustments to get a clean shed..

everything I have read about tying up a counter balance loom says,

1) make all the sheds even

2) make all the lamms even

3) adjust the treadles..

but what do we adjust to get a clean shed.The treadles?Lamms? and howdoI know which way to adjust them,up or down, I have texsolvy on the lamms and tredles..

The previous owner had a great deal of trouble setting it up too..

are the treadles suppose to be close to the foot rest,or higher?

I am so confused and stressed over this loom...

thanks carole

ok, the 2 top rods are even, the lamms are all even and all  lthe shafts hang at the same height.

when I press on treadle 1&3 this is what the shed looks like

when I press on treadles 2&4 this is what the shed looks like

 

this is what the lamms and treadles look like when everything is at rest

Comments

Sara von Tresckow

It appears that the threads in the center of the shed are always from the same shaft.

I'f recommend looking at all the cords and points of attachment for that shaft. It could be that something is preventing the frame from moving when you press the treadle.

ReedGuy

Like Sara said, there is a tie-up problem. Have your hubby look at the shafts as you press the treadles and see why it's not going up or down. Just a quick glance at your last photo and it appears the hook has jumped the lower shaft bar on #2 (counting from closest to you).

laurafry

In the first photo it also looks like you may have two threads crossed between the heddles and the reed.  Althougth this is probably not the shed problem, if you can get the sheds figured out this will be a problem for your actual weaving.  If it *is* crossed that is....

Good luck!

Laura

caroleg51

this apprears to be a very sticky yarn,it is sock yarn.. I double checked all the threads going through the reed andheddles, I fixed 2 threads but someofthe others seem to just stick to each other . But I dont think that is the shed problem. All the frames move up and down as they should when you press on the treadles, I press on # 1 and 1 goes down,pres 2 and 2goes down etc.all the lamms are level with each other. we held the shafts striaght and double checked the lamms, everything seems to be level.. but when we let go of the shafts , shaft 3&4 sink alot, like they areheavier then 1&3,but I know they are all the same. Should 3& 4 sink like that?

carole

lkautio (not verified)

Photos of the top from the front would be helpful. Hammetts are generally thought to be good looms, so don't give up.

Since you are coming in from a rigid heddle, I'll ask a possibly dumb question - does every thread go through a heddle (rather than every other thread)? I can't tell from the pictures.

Laurie Autio

sally orgren

Maybe a loom intervention is in order if someone lives close by...

caroleg51

Laurie

yes,everything threadgoes though a heddle..

Iwilltake afew toher pictures from the top.I am assumng your meaning the top of the warp from the front?

caroleg51

Sally.I had a lady graciously come by and take alook at the loom.. she had never seen a hammett loom and we spent a few hrs warping it and tring to make adjustments and she left asfrustrated as I am. I do not have any quilds close by,nor shops and  other then on line chat, I dont know anyone who lives close by that would be willing to come and help me. I sure wish I knew of some one.. Hubby and I have been trying for 2 months now to set this up,and I feel like  I have a new car I cant drive.. I want to weave!I am in central arkansas,  near hot springs,if anyone sees  this post and is willing to help

thanks carole

 

caroleg51

Laurie

here are some pictures of the top of the warp and the postion of the shafts using each pair of treadles.this one is using treadles 1&3

this one is using treadles 2&4

this is  a picture of the shaft position using treadles 1&3

shaft position using treadles 2&4

side of shed using threadles 1&3, after a warp adjustment

side of shed after a warp adjustment using treadles 2&4

does this help any?

thanks carole

Robin Murphy (not verified)

Carol, you mention pressing two treadles at a time... I wonder if your loom is a counter balance and should be tied up differently than the way you have it. You said the two top rods are even...that sounds like it might be counter balance and would have a single top rod also... they are called rollers. I believe Hammet made a jack-style, too, but am not sure if it was a reverse jack... you say the shafts lower when you press a treadle, that would be reverse jack style.

Photos from the front of the loom, showing the castle and some showing the treadle and lamm tie-ups might help. It looks like the shafts are not rising and falling the same distance, perhaps your treadles are not level.

If your loom is counter balance, this Leclerc web page might help you with the tie up.  http://www.leclerclooms.com/draw_inst/fanny.pdf

I wish I could come help you.

Robin

sequel (not verified)

This is not a Hammett Marcoux jack loom.  It is a Hammett standard sinking shed counterbalanced loom. 

Your photo showing the shed produced by shafts 1 & 3 show that shaft 3 is not going down as far as shaft 1.  Did you manage to get a manual for your loom?  Hammett tell you how long to make the ropes for the upper rollers and the lower rollers.  Your lower pulley ropes look kinda short. You can check by making sure the warp goes in a straight line from the breast beam through the heddle eyes to the back beam.

Also make sure the direction of the wraps around the rollers is correct.  The ones that show in the photo are not the same.  Both of the rollers are wrapped in the same direction on left and both are wrapped in the the opposite direction on the right.

Make sure your tie-up is correct and you have no treadle ropes hanging up on neighboring treadles or lamms.  Big knots in the pulley ropes (or Texsolv pegs) will create problems too.

Don't send this to the burn barrel.  Lots of rug weavers are looking for these looms!

caroleg51

Robin,it is a counter balance loom, I know  that for sure. To test the loom, I was pressing down on treadles 1&3 and 2& 4, as a tabby would be woven.Which I have it warped for. I wanted to try just a plain tabby weave for the first time. So, I have each shaft tied to one lamm and then 1 treadle tied to 1 lamm . Is this not correct? It does have a large diamater roller bar at the top and then 2 smaller rolling bars that hang by cords from that larger roller bar. Here is a picture of the loom from a distance.These pictures were taken at the previous owners home before we took it apart to take it home, She had the sameproblem getting the treadles and shed correct, but she eventually  got it so she could weave on it..  Thanks carole

 

caroleg51

 Sequel

thanks or your replay.. I did get a manual of sorts, its not much help in the set up though.  As close as I can tell, the warp does go in a straight line from the front to back beam. Are you saying the ropes on the small rods are incorrect? should they be going in oposite directions on different sides, left side one direction, right side the other direction? Except for changing the lamms and treadle heights, this loom( rope on pulleys etc) are exactly as they were when the previous owner had it)

so what do I adjust to make shaft 3 go  down as far as shaft 1?

 

thanks carole

caroleg51

 so if I weave with the sheds not even as they are now, what happens? If i do a tabby weave?

ellows (not verified)

My husband just made our two harness Hammett into a 4 shaft loom and he had trouble too. Don't threw it away, it is a great loom. Is the nail on the rollers that holds the cord on the bottom? Does the cord go around 1 1/2 times? Are your treadles original? We had to put weight on two treadles=1 pound each because we added treadles. Make sure that all the eyes of our heddles are lined up with the center of the reed. Have you checked that there are the same number of heddles on each reed, they add weight. Hope this helps, keep working on it.

Amy

caroleg51

Amy

yes, the treadles are original, it looks to me that the warp goes straight from fron to back evenly..The cord does go around 1.5 tiems.I will  have to check to see where the nail is. I have notcounted to makesure eah shaft had the same amount of heddles per shaft, I will count them tomorrow though.. I am beginning to think this loom is cursed! The previous owner had lots of trouble setting it up too.. I have never been so frustrated with something in all  my life. I paid a good chunk of money for this loom and I want to weave on it! This is just crazy.. my problem is I am a brand new weaver and I dont know what to change and how much to make it all correct. Any chance you live in arkansas?? I could rent your hubby to come and fix my loom! LOL

thanks carole

thanks carole

caroleg51

I did get the manual from Janet ,but it has very little info about tie up, its mostly on how to put the loom together

ReedGuy

You may find this book by Leclerc a tremendous help. It shows a similar loom and lots of info beyond assembling a loom. It's a PDF file about 11.6 MB.

Leclerc's Warp and Weave book

This loom should work, it's just a matter of learning the methods required to make it function. ;)

 

caroleg51

Reed guy, thanks,I already had this book. The only thing I can see is I will check to see if the cords holding the harnesses are wrapped in the opposite directions.  This book also,like all the others, does not tell " what partof the loom" to adjust whenyou have problems. I think all these loom makers assume that people have been weavers for a while and know what items to adjust and how much,None ofthe books have said, well if you dotn have a clean shed," adjust this" Thats my problem, I dont know what to adjust to make that clean shed..

thanks carole

sequel (not verified)

When you step on 1&3, both go shafts down, but shaft 4 doesn't go up as far as shaft one.  So something is interfering with it. 

The Edward Worst book, Weaving with Foot Power Looms, shows the proper way to tie up a counterbalance loom.

And the shed has to be clean in front of the reed (closest to the weaver), but not necessarily behind the reed. 

ReedGuy

The trouble with Worst's book it is on old looms, not on rigid heddle looms. Back to the Leclerc book, if a shaft is not high enough or too low, well you have to look at what mechanism controls this. A loom is a simple machine. I know it doesn't seem so when it doesn't work the way it's expected to. It could be tension or it could be cord length on the lamms and treadles and over head rods or maybe the lamms are fetching someplace. Are the shafts and lamms hitting any place when you press the treadles that might restrict their movement? I would also think that the shed should be as wide open as possible so that the warp is down on the shuttle race and not up off it by more than 1/4", same at the top. It acts like somwhere along the line the cord lengths are off. If it wasn't working right with the previous owner, perhaps her methods were wrong and passing this along does not help. The shaft that is not rising high enough, take it by hand and make it rise and see what's interfering, with one of you holding down the treadles. That one shaft is not moving so see why by examining the mechnaism involved with the working shafts. It should be obvious because the system is open and viewable, not closed.

caroleg51

Sequel

so are you saying  that I should be looking at the shed in front of the reed, I presently have the reed locked in upright position,and we were looking at the shed between the reed and heddles.. 

thanks carole

caroleg51

We did it! we finally got a clean shed! I dont know what we adjusted, because we did  it so many different times. but we adjusted the cords from the rollers to the shafts and adjusted the shafts to the lamms.. but what evern we did, we finally have a clean shed to work with.. I dressed the loom with sock yarn I had and did not realze it had a little stretch to it, and I dont think it is going to produce a good product, but for now,I am going to practice on it and then will rewarp anew one.. Now that we have a clean shed,I am seeing that the lamms still go up between  the harnesses when I press on the treadles,so I am assuming that they are suppose to do that ?

Thank you from the bottom of my heart for all your suggestions. And my loom thanks you . It has been saved from the burn pile LOL

oh, now  that I have a shed and a warp on it, I wove a small header on the scarf,using a stick shuttle that I already had yarn on,and then tried the boat shuttle.. I am short and can hardly reach the shuttle race to try to throw the shuttle.. Am I doomed to using only a stitck shuttle.. Any suggestions?

Thank you ALL!

carole

now a happy weaving camper

gailc

Are you sitting high enough at the loom?  You cant be much shorter than me (unless you are 6 yrs old), and, although photos can be deceiving, your loom doesnt look exceptionally deep, so you shouldnt have trouble throwing a boat shuttle.

ReedGuy

Your not sitting high enough for your elbows to clear the breast beam and maybe not close enough. Did you have an adjustable weaving bench with the loom? If your sitting in just a chair it's not going to work unless it's a lot lower than I'm thinking. Never used any other loom than my own countermarche I made. The cross member by the ends of the treadles is a foot rest on many looms I beleive. It aids in beating when a foot is held to it.

Pay attention to the details of warping and tying up your loom, it's the only way your going to remember it and enjoy your time with it.

caroleg51

I am sitting on a arm less office chair that is height adjustable.  My loom did not comewith a bench but I did get one but it way too high for me. I am 5'1 inches. I can only sit on the edge of my buttocks on the bench and my feet barley touch the  floor, it is very uncomfortable. I dont know if I want to cut the legs down or not.

 

sequel (not verified)

The bench that came with your loom was 29" high.  I'm 5'2" and I don't have a problem with the treadles if they are tied high enough for my feet to reach them from a tall bench.  Of course I can't hop up and down real gracefully.

caroleg51

my bench is not a hammet bench, it actually has no name on it, but it definately too high for me, it came with a macomber loom that I got.. I was thinking of trying a keyboard bench, nice and padded and is adjustable and not expensive at all, walmart sells them

weaver-dyer (not verified)

If the bench is the correct height for your arms, but you have trouble reaching the treadles, you may want to put blocks on the treadles. 

Janet

caroleg51

the bench is too high, my feet dont touch the ground, but when I am sitting in my office chair I can reach, but the treadles come high and I am short so I have to lift my legs up quite a bit to reach the treadles..

But on the office chair, I really dont sit high enough, I cant reach to throw a  boat shuttle. I need to use a stick shuttle

carole

ReedGuy

When I weave and treadle my feet never touch the floor. One foot on the bar in front of the treadles and one on a treadle. You will find a good many looms are set up this way. Some looms even need to be jacked up on blocks for the weaver.

Dena (not verified)

And, not all looms fit all bodies.  I have had some fabulous looms that I had to sell because it just wasn't right.  Good luck! 

Joanne Hall

Hi Carole,

I noticed in the photos of your shed that the shed was probably bigger than is needed.  It only needs to be 1/4 or 1/2 inch more than the height of the shuttle.  So, if you consider that you don't need to open the shed that much, you can either just not push the treadles down so far, or you can lengthen the treadle cord.  Which you decide to do would be dependent on your comfort at the bench height you have.  Either way, you will then not have to raise up your foot to put it on a treadle.  It might also be good to tighten your tension on the warp.  That will give you some resistance so that you won't open the shed too much.

Joanne

caroleg51

Dena

I am starting to realize that.. Right now, I am not comfortable weaving on this loom, but I am still trying various seating options. I hope I can get it to be comfortable.. It seems like a good loom other wise

carole

caroleg51

Joanne

oh thanks sooo much, I am going to lower the treadles so they dont come so high.. I did see that it had a very large shed and I just though that it was suppose to be that way so you can put rug shuttles through it..I will definatly try lowering the treadle cords.I am just sooo happy we finally got it adjusted so I dont have split sheds on it.

thanks carole

Calico_Raven

adjusting the counterbalance loom is a try as you go thing, on mine even flipping the cords would correct the problem. once in a while the lamms would catch on each other,  as mine doesnt have side tracks, so you have to pull the lamms apart. i loved mine once I got it balanced.

caroleg51

it sure has been a challenge to get it all balamced, well the best we can do for now.I am gojng to adjust the treadles to see  if that will help with the problem of lifting my legs to press on the treadles..so much to learn .I appreciate everyones help

sequel (not verified)

Be careful.  I have one (and love it).  You need to sit squarely in the middle.  If you sit on the ends, say, to lean over and pick up something, it'll flip over and you'll land on your rear end so fast you'll chip your teeth!  The higher your adjust it the riskier it gets.

caroleg51

sequel

are you talking about the treadles or the bench? Sounds like the bench.. I am really thinking my office chair is going to be the best seating, at least thats the best so far..

peggychurch@ea…

I am in the process of adjustiing the cords on my old Hammett loom.  That is quite a saga you had to get it right.  Could you please measure your cords?  I would like to know the distance between the top roller and the bottom roller.  And the bottom roller and the shafts.

I set it up with the treadles hinged at the bench to avoid having to find the ends of the treadles.

Submitted by caroleg51 on