Help fellow weavers! in the back of my warp I keep getting all these threads that cross over each other and get all knotted and twisted up. I've been keeping my lease sticks in to help the tension because this thread crossing happens every time no matter how careful I wind and beam. I don't understand why it's happening. Does anyone have any tips on how I can get a nicely beamed warp with no thread crossing? Im already well into my weaving so I cant untie and de tangle, plus new warp crossing seems to happen whenever I advance my warp. :( also for some reason my cross always gets tangled when I'm beaming. I recently learned a Scottish warping and beaming technique and I have been using it but seem to mixing it up with the regular back to front method and am now doing this hybrid of the two which seems to the reason. But now I can't remember the original back to front method. Help! These crossed threads are ruining my warp.

Comments

sally orgren

Yes, that is likely the problem.

Back-to-front uses lease sticks. You start by securing your warp to the back beam, and the leash sticks keep the warps in order by holding the cross, and providing a bit of even tension while beaming.

Once beamed, next you thread the loom, sitting at the front of the loom. If you can drop your front beam down to the floor, or remove it to ease access, that is great. Typically the lease sticks are suspended between your castle and the back beam, so you can pick off the exact warp you need, in order, as you thread.

After threading the heddles, you thread the reed, and tension. You should be ready to weave!

With front-to-back beaming, you don't typically use lease sticks. You start by threading the reed and it serves to spread out your warp and hold the warp order when you thread the heddles. Also, you thread from the back of the loom, so you have to remember this when reading your draft. It might be easier to place your draft upside down as you sit at the back for this task. The last thing you do is beam your warp after the threading is complete.

Hopefully, the crossed warps are far enough back from the castle and weaving area they are only a minor nuisance. If you have a fairly short warp (3-5 yards) on a floor loom, I am thinking you might get by okay. Yes, it doesn't look so pretty, but as long as you are getting a good shed and no warps are breaking, keep weaving and plan to improve your technique on the next warp!

Dawn McCarthy

When placing threads in the raddle - spread the looped ends evenly across the apron rod.  It usually happens by default but if your radddle has wide sections, the end warp loops can sit on top of one another, hence a little overlapping or crossing behind the lease sticks.  Make sure you are beaming with plenty of tension!  

Dawn

sally orgren

Duh. I completely forgot about using the raddle when warping back to front!

Once I secure the warp to the warp beam, I typically clamp the raddle to the top of the back beam, or suspend it between the back beam and the heddles. (Depends on which loom and how much space is between the castle and the back beam.) My raddle has 1" increments. I use rubber bands over the nails to easily keep the warp bouts from jumping out of position.

With the lease sticks suspended between the raddle and the castle, once the warp is beamed, I use the lease sticks to keep my warp threads in order for threading the heddles.

-----

One thought occurred to me. If I accidentally twist the bout when transferring it from the warp board to the warp rod, that can sometimes lead to warp threads looking tangled at the back of the loom as they feed into the lease sticks. Between the lease sticks and the castle the warps are perfect, but feeding up from the warp beam to the lease sticks can look *quite* messy if this happens. 

Penn (not verified)

I can't advise on the crossing threads (and see you've already gotten help from the pros anyway), but wondered about this: "I recently learned a Scottish warping and beaming technique . . ."  I understand that you've gotten it mixed with another technique, but can you describe the Scottish method at all?  I'm interested in all these secret alternatives to B/F, F/B, etc.

heatherbarrick (not verified)

like another commenter said. if you twist your bouts at any point between the warp board and tieing on and beaming you will have warp threads that cross no matter how careful you are with keeping your cross when you are threading. my advice is (since you are already weaving and dont wand to redo any thing) create one tabby shed, place a lease stick in it behind the heddles but in front of the back beam.make the oppisite tabby shed and place another lease stick in line with the first behind the heddles. now you have your cross intact again. you can gently work those sticks back to the back beam and you will have a cleaner shed to weave with. you with have to gently work those sticks back every time you advance the warp until you are either done or to a point where you want to cut off and untwist everything.

kmrussell (not verified)

Is there no way to keep the bouts from twisting when they go on the warp rod? I would think that this twist might create some uneveness in the tension. I'd love a solution since I have this problem but only on some of the bouts and can't figure out what I'm doing to create it. Thanks. Karen

Joanne Hall

When you are about to wind on your warp, the lease sticks are very close to the end loops on the warp beam tie-on bar.  The distance is less than 2 feet.   If there are twists between them, you just straighten the warp on the tie-on bar, according to the lease sticks.  You don't want lumps from groups of threads on the tie-on bar, as that creates lumps on your warp beam.

When they are straightened, there will be no twists in your warp as you wind on.  The cross in the lease sticks keeps the warp winding on smoothly and orderly.

Joanne

Submitted by Greatlakes on