If you have a pattern for dish towels that does not say how many towels the specified warp length will make, is there a way to figure this out?

Comments

Joanne Hall

Four yards makes about 4 towels.  A longer warp may make one for each yard which are larger towels or perhaps one more towel than the number of yards of warp.

Joanne

twoquinns

And if no yardage is given? Here's the information I have: huckaback, 16/2 cotton, 19 1/2" x 31", 30 epi, 692 threads, 23" width in reed, 30 ppi.

Lauries (not verified)

That looks like a finished size of one towel. So you would add yarn waste, and that would be your warp length for one towel.

Sara von Tresckow

Just do it - figure about a yard per towel and add loom waste.

If you run short on the last one, make it a dish rag - and start over learning from your calculations on that warp.

twoquinns

Yes, I assume that's the size of one towel.  But am I really winding 692 threads for one towel???

loomroomcat (not verified)

16/2 is very fine yarn, probably calls for Cottolin.  If you use 8/2 unmercerized cotton and thread  at 20 epi, you would not need as many threads (390).  I make my towels 19" wide by 30" long.  On my loom, I figure 24-30" for loom waste, so one towel would require the threads to be approx 60" long each.  I personally would put on enought to do at least 3 towels at one time, so I would put on about 120" of warp (you don't need to figure waste for each towel if you don't cut them off individually).  You will have to modify the threading pattern for less threads. 

twoquinns

Oh, wow, I hadn't even thought about having to change the threading pattern if I use a different size yarn.  I'm glad you mentioned that.  And since all the color changes are in the warp, I'd also have to change how many threads I wind of each color.  Just how do I go about figuring out both of those changes?

amyfrey (not verified)

Often if there are two different designs in your pattern you start and end with one of the designs so you have A-B-A-B-A etc.  In which case you delete as many A-B pairs as you need to get down to appoximately 390 threads.  If the designs are combined so that there is just one unit to repeat, there will usually be half of the pattern either at the start or the end to balance the design.  So again you delete as many of the repeats as necessary but be sure to keep the balancing half pattern,  Unless you are using up odds and ends of thread, just start winding the warp following the color pattern.  There is enough thread on a cone to make several towels.

jander14indoor (not verified)

The number of threads in the warp has nothing to do with how many towels you weave.   That's driven by the LENGTH of the warp.  With your current pattern you will use 692 threads for one or one hundred towels depending on the length of the warp.

Number of threads is driven by yarn, width desired and weave structure.  Others have already suggested how you might modify that.

Jeff Anderson

Livonia,  MI

loomroomcat (not verified)

Many times there will be a section you thread that is repeated say 10x.  You can make adjustments there by only repeating that pattern 5x.  The huckaback pattern I wove had two distinct threadings.  One having a 1-3 1-3, 2-4 2-4 repeat, and a 2nd with 1-4-2-3 section.  You can make adjustments in each pattern to get the desired width.  I personally don't care for symmetry in my weaving so I make adjustments as I thread, when I get to the desired width, I quit.  If making them symmetrical is desirable to you, it takes a bit more planning.

the 1-3-1-3, 2-4-2-4 section gives you the checkerboard pattern and the second threading gives you the sections in between. 

loomroomcat (not verified)

Ha!  Just looked at my profile pic, it is a huckaback pattern.

 

twoquinns

Yes, loomroomcat, I had noticed your pic was a huck pattern!  Thanks to everyone for your help.  I know you must get tired of helping us newbies all the time, but there's so much to learn.  Please bear with us.

Submitted by twoquinns on