I've just located a 48" Varpapuu loom on Craigslist.  I'm interested, and have emailed the seller with several questions.  One that I'm asking the seller, and would also like input from this group, is regarding harnesses & treadles.  The loom is advertised as 8H & 8T.  I find that a bit unusual, as there are generally 2 more treadles than harnesses, except in direct-tie-up looms like the smaller Harrisvilles.  Is the same number of treadles as harnesses common to the Varpapuu?

For those of you who have or are familiar with Varps, what would be critical questions for you to ask before you drove 5+ hours in one direction to check out a loom?  I do know it's an underslung beater, which is what I'm used to on both my counterbalance & Macomber.

Thanks for sharing your knowledge!

Peg

Comments

Dawn McCarthy

Most Swedish style looms that originate from outside the US have the same number of shafts and treadles, the Varpa is a great heavy duty loom.  8 shafts and 8 treadles is not unusual.  As long as the loom is in good condition and square I think you will be very happy with it!  I have previously owned one and loved it!

Dawn

Peg.Cherre (not verified)

Interesting, Dawn.  So how do the Swedes handle tabby?  Or are the looms usually tied up to require multiple treadles for one pattern pick?

Can treadles be added for tabby?

Peg

SallyE (not verified)

Adding treddles to most looms is really easy.   I think I've added treddles to almost evey loom I've got except my 40" Macomber, which came with 18.

All you do is make more based on the old ones.   Sometimes you have to move the support brackets apart a little (drilling new holes to attach the brackets) and get a longer rod to hold the treddles.

On a Varpapuu, I'd suggest not adding treddles until after your first warp.   That will give you an understanding of the shed mechanism.   Putting treddles too close to the lam pivot point makes things difficult, and putting them on the other side can mean that the chords from the lams don't reach down vertically.  The amount of space you want between treddles for your feet to fit also figures in to it.

 

 

 

Peg.Cherre (not verified)

Thanks, Sally.  I would never make any modification to a loom till I really understood it.  In fact, I've been extremely hesitant to make any modifications to my 2 looms, for reasons that aren't clear to me.  I am still curious how the looms were intended to weave 8 harness patterns plus tabby - multiple treadles for 1 pattern pick?

kerstinfroberg

Peg, the short answer is: we don't. Use tabby, that is.

The longer answer: there is a reason we bundle most pattern-and-tabby techniques into one category: simplified dräll. Dräll is usually understood as two (or more) blocks, woven in turned twill or turned satin. (Historically, and perhaps etymologically, dräll probably was used to mean "patterned".) The fact that we call overshot, crackle etc "simplified" drälls indicate that we see it as a "lesser" way to make patterns... once we have the number of shafts, we go for "the real thing".

Techniques like S&W were unheard of until Väv introduced the idea some years ago (ok, maybe 20 yrs now, but we have been weaving for a lot longer). And I don't think I have seen any more-than-4-shaft technique requiring tabby mentioned in any Swe book, but I may be wrong there.

Peg.Cherre (not verified)

That's great info, Kerstin!  I must try turning some drafts - I've not gotten the hang of it.  

kerstinfroberg

or, in Swedish, dräll, has nothing to do with "turning the draft". It is the will structure that is "turned": one block weaves in warp twill, the next in weft twill. There should be a clean cut between the twills. Like this (but it can be done on other numbers of shafts, in point twill, in broken-reversed twill - or in satin. But then of course it would be called turned satin... even though it is still dräll in Swedish):

Some might call this something else in English, but at least Fiberworks is with me :-)

lolly1965

Hello I have done a turned twill tie up and am battliing to get  a good  shed  on the loom?Tabby treadles 9 and 10 are perfect but treadle 2 and 8 are not ,so much so that I cannot throw a bobbin as the lower shed is uneven.I have spent the last 6 nights re-doing the entire tie up 6 times and am at my wits end.

I  have so many conflicting hints some say variance in back cord to front in length others say that with the Varpa if your upper lamms are at an angle the uper lamm cords must be 2 notches away from taught and the lower lamms taught.

I am some what OCD with most things and have gone thru the exercise over and over.Any adjustments done afterremoving steel pins has helped but still do not get an excellent shed on shaft 8?

Oh and I have also done both options of LEVEL lamms and angled  with the same result.

I have two other looms ,4 shaft 6 treadle and am able to get perfect shed ,my one loom has a 2m reed and flying shuttle.

I am

totally frustrated at the moment ........any suggestions.

ShawnC

Hi Lolly,

So sorry to hear you're having trouble with your Varpa! I have 2 and really enjoy them. What model do you have? I have lovely sheds on both my CM and CB.  I am going to hope that Joanne, Dawn, Sally or Sara jump in here to help, because all I can really suggest is to look at Joanne's pdf (http://glimakrausa.com/wp-content/uploads/2012/05/intro-cm.pdf) and try it all again. I would think since you get a good shed on your tabby treadles (did you notice the tie up for turned twill above?) that it must be something in the tie up is crossed, etc. Sometimes it's very easy to miss the obvious (says someone who has done it too often).

MaryMartha

Lolly, when you depress treadles 2 or 8, are any of the lamms or treadles touching?  It might be that treadles 9 and 10 ride up, only on certain sheds, restricting the motion of the lamms.  If those "perfect" sheds are bigger than they need to be, decreasing the height of the sheds by lowering those treadles might improve the others. 

As noted above, these looms were designed to have the same number of treadles as shafts.  Tying up two additional treadles is sometimes a challenge, especially if the loom is narrow.  For the turned twill you don't need tabby sheds.  So you could tie up the four treadles to either side of the center cords, or tie treadles 3 through 10 for your turned twill, and leave 1 and 2 untied. 

On my Karelia (taller than the Finlandia),  I tied the lower lamms parallel to their pivot bar, and the upper lamms angled 2 inches higher than the upper pivot bar.  This prevents upper and lower lamms from hitting each other as the sheds open.  I might angle the lower lamms also, if they are being hit by the treadles and I wasn't able to tie the treadles lower.  My loom had four holes for the two pivot bars.  With 4 shafts, I'd use holes 1 and 3.  With 8 shafts, I might use holes 1 and 4.  In any case, you want the distance from bottom shaft bar to upper lamm, between the lamms, and from lower lamm to top of the treadles (in back) to be roughly the same.

You do need slack in the treadle cords at the front of the treadles so that all the sheds can open.  This is independent of the position of your lamms.  There are two ways to go about this.  One is to peg treadles from front to back. Start with the top of the treadles about even with the bottom of the foot beam,  tightening up gradually on the cords as you go -- usually one cord hole for every 2 or 3 shafts. The other way is to peg from the back - with the treadles propped up to the desired height, making the cords from the back two shafts taut and then gradually easing up as you come forward. 

The bottom of the shed is controlled by the downward motion of the upper lamms. Ideally, the bottom of the shed should sit slightly up from the bottom of the reed.  When you open the shed with treadle 2, the warp threads on which shaft(s) are riding up?  Are any warp threads riding lower than most others, or so low they are being pushed up by the reed?  For each problem treadle, write down which shafts need to move down and which ones up.  I like to raise or lower the shaft bars with my hand to be sure I've identified the right shaft.

With the locking pins back in, shorten the treadle cord to the upper lamm for a particular shaft to move the threads down. Lengthen the cord to shift the threads up.  In any case, don't move the peg more than one hole at a time.  Take your time.  Take the pins out and check again. Once you are satisfied, recheck the other sheds.

What if the cord for the shaft you identified runs to the lower lamm?  Two possibilities - the more likely may be that you isolated the wrong shaft, which is easy to do.  The other is that these threads really belong at the top of your shed and are riding low.  In that case, you need to adjust the cords to the lower lamm in the opposite motion -- shortening the cord to lift the threads up.

One other thing -- and I only mention this in case you are not accustomed to hanging beaters.  You need to push back on the beater with your throwing hand to clear the shed at the same time you depress the treadle.  With the beater at rest at the bottom of its arc, you are not really seeing the shed.  Often pushing back an inch or two (this is your throwing position) will align the bottom of the shed cleanly.  Clean sheds also require sufficient tension. If the warp tension is low, try cranking it up a notch or two. 

Sorry if this is overkill.  Without pictures, it is easy for the imagination to run riot.  It is a fine loom - just takes a bit of getting used to.

I highly recommend Joanne Hall's book, Tying up the countermarch loom.  I found those instructions worked well with my varpa.  The only exception is that the varpas are designed to have lamms of equal length, rather than long and short.  So where the book says "short lamm", substitute "upper lamm" instead.

Submitted by Anonymous (not verified) on