I have my Cranbrook loom all set up and dressed.  I have a lovely weaving space - a large loft open to the rest of my home.  I came across the Cranbrook 2 weeks ago, but I had to wait until I sold my 46" 8-shaft Kessenich jack loom before I could set up the Cranbrook.  It was harder letting that loom go than I had thought it would be.  It was my first floor loom and I had it since 2004.  I wove a lot and learned a lot on it, but it has now gone to a fairly new weaver and hopefully she will have as much enjoyment of it as I did.

I am not sure if I like this Cranbrook or not.  This is my first experience with a counter-march loom.  All my other floor looms are jack looms, actually they are all Kessenich jack looms.  The Cranbrook is all dressed now, all 8 shafts, all ten treadles.  If someone would have come up to the loft this morning with an ax or $10.00, that loom would have been history!  I figured that with the size of the loom that there would be all kinds of room to work.  There is not!  I could not get comfortable threading, there is no place to sit without something in the way or a really long reach.  My jack looms are much nicer to thread than this monster.  And as for those texsolv heddles - they do not slide, they jump on top of each other and will not move, the threading eye is side-ways....EEK!  I will say that it there is very nice motion to weaving on it, I like the hanging beater a lot.  I am still working on getting comfortable on the treadles - they get a little tricky still.  I am not used to having to get up to advance the warp, but I think that is just because it is a 62" loom.  That part was a surprise when I got it home - it was represented in the ad as a 45" 8-shaft, but its 62" wide.

I hope weavers that have a lot more counter-marche experience will reasure me that things will get better.  I would love some ideas on how to thread the beast in comfortable position.  I really do not want to fight the loom everytime I dress it.  Here are some photos

Comments

Cheryl Muckenfuss (not verified)

I have not worked on a Cranbrook, but have worked on Glimakra looms. Looking at your picture, it looks as if you can remove the beater, the breast beam and cloth beam, put a stool or low chair to put you at eye level (or raise the harnesses to eye level). You should have a locking mechanism for the harnesses as well as a harness holder. This will make the Texsolv heddles slide more easily as you thread. I am assuming you are dressing the loom back to front. If you are going front to back then you should be able to fit in the back of the loom behind the harnesses and in front of the back beam. If so, then again utilize the locking mechanism and harness holder; adjust the harness height for threading if need be, dependent upon what you are sitting on. The only problem may be with fitting a seat in between the treadles. As I recall, the Cranbrook has a gate for the treadles so not sure if you would need to remove the treadles in order to get a seat in the front or back side of the harnesses. HTH somewhat.

Cheryl

Dena (not verified)

I recently acquired two Bexell Cranbrooks (life is abundant!).  I set up the first and was surprised at how small and uncomfortable it was.  I expected the second to be the same, but when I set it up, it was much bigger and easier to use.  Exact same design, except for size.  The big one is from the "J" series, the small one from the "K" series (check the plaque on the beater).  The bigger one was a pleasure.  I haven't liked weaving on the smaller one, but I ran a workshop and had four students weave on it who really liked it.  I think it's a matter of which loom fits your body better and what you're used to.

theresasc

I did remove the breast and knee beam, but I really do not want to remove the cloth beam everytime I dress the loom and it is really in the way.  The handle has a screw holding it on and I am afraid that I will just wreck the wood by contantly taking it out and putting it back.  It does not have a sleeve, just screwed right into the end of the beam.  I ended up sitting in a chair with my legs over the cloth beam and leaning forward to thread.  Very awkward and tough on my back.

sandra.eberhar…

You might look into other ways to attach the handle.  Without a picture, I can't offer any suggestions, but there are usually options.  If a screw is the only alternative, I would fill the screw hole with epoxy, and drill a hole slightly smaller than the screw.  Wax the screw and drive it in.   Now you have a hard, stable place for the screw.  My cloth beam is also  in the way, but I put a cushion on it and kneel on the beam as I sit on a chair drawn up next to it.  It sounds odd, but it actually looks like an ergonic chair that used to be sold for offices, and is very comfortable.

Submitted by theresasc on