I've been reading through the forums and looking at projects all about towels.  I mostly weave on an inkle loom but i'd like to start using my 4-harness schacht more often. I'd like to try some towels for christmas gifts and I've had some success making a thing that looks like a towel :)

So here's my question...

When you warp a loom for towels (more than one)... How do you know where to stop one towel and start another? This has me so perplexed I can't even express it!

If you can offer and guidance here, I'd really appreciate it!

~JD

Comments

jlread (not verified)

Hi....my method is to use a length of string ...a knot tied at the correct length.....then use a straight pin to attach this string at the beginning of the woven towel.  As the weaving progresses you simply use the string to check length...when you reach the correct length, use a brightly colored yarn to mark the end of one towel and the beginning of a new one.  Reattach the marking string to the beginning of the 2nd towel...on and on...really simple.

endorph

that is the length of one towel (pre wash length) I pin it onto the selvedge and as I work my way up just keep moving the pin up the ribbon. When the ribbon is through the towe is through. Take into account your hems etc. I have done it with both the length of just the towel without the hems and also with the hems included. Does that make sense? I have also used stitch markers - like the ones used for knitting - and place one every five or ten inches. Then you can jsut count your markers and know when you have reached the end of the towel. Tina

laurafry

One caveat - when using a ribbon, do not roll it into the cloth on the beam but let it hang loose.  :)

I have several 'ribbons' of various standard lengths for towels, scarves, shawls.  I tape the end so they don't ravel and mark the length on the tape so I can easily find the correct length for the project at hand.

cheers,

Laura

JDStar (not verified)

Thank you so much!

Now I am wondering though...My table loom is not very big. As I weave, I have to constantly advance the warp because I can only weave a couple of inches at a time. By the time I finish a dish towel, half of it's going to be wrapped around the front winder (can't think of the right name).

I'm concerned about the towel being pulled tight on the loom and not getting the right length measurement because of that.

I'm still learning about draw in and shrinkage and what not. Have avoided it to this point (aversion to math). But I did at least finally figure out exactly how much I need to figure in for loom waste.

Any tips on that?

PS, thank you SO MUCH for your fast and super helpful answers!

~JD

endorph

I had to smile at your comment regarding roll up the ribbon - been there, done that! I make sure I have two loose ends every time I advance the warp and repin the ribbon! Tina

mrdubyah (not verified)

I just use a piece of 8/2 cotton in a contrasting color.  I tie one end to the first hem, cut it off at the desired length (e.g. 26") and let it roll up with the cloth.  When I get to the end of the string, the towel is done.  I throw in a little space (or a contrasting yarn), start a new towel, and tie on a new 26" piece of cotton for the next towel.  The cotton is wrapped around the cloth beam along with the cloth so I don't have to worry about tension.  However, I usually do assume at least 10% shrinkage during finishing for cotton dish towels and try to build in enough length and width to account for that in the finished towel.   Enjoy!

JDStar (not verified)

Wanted to let you guys know that I finished 6 dishtowels yesterday using a lenght of ribbon and marking it with a pen.

My dishtowels are all the same length and I am just tickled pink!

Thank you VERY much!

naturalfibres (not verified)

I just use a measuring tape and two long pins - I just leap frog the pins up the tape as I advance my warp, making sure to not roll up the tape around the front beam.

Submitted by Anonymous (not verified) on