I have now successfully completed three projects -- all of them scarves of varying patterns/widths, with wool or acrylic yarn (didn't like acrylic, much, but it worked)  -- as I am still very much learning. I bought some new yarn to make a 4th practice piece identical to the very first one. So this is a tabby weave with a straight threading. After I was done beaming, I noticed the yarn was sticking; when I went to check the shed it was all completely stuck together. Not crossed or skipped, STUCK like felt. Eventually we got it all separated. We tried to adjust the tension and weave a header, but all that produced was a reed jammed with fuzz and 3 or 4 broken warp threads. It will take me all day to clean the reed out.

 This yarn is "100% Peruvian wool"  by Stitch Nation/ Coats&Clark, I wrapped it around a ruler to make sure it wasn't too fat (it wasn't). Now I'm afraid to buy yarn, since obviously I chose poorly. Now that I own it, I can pull on it hard enough and see that it tears (it doesn't snap so much as slowly shred to pieces) but I can' t very well sit at JoAnn's shredding the merchandise.

Comments

Michael White

When you say the yarn wasn't too fat, what size reed are you using.  A lot of yarns that abrade (make fuzz) do a lot better in a bigger reed sleyed 2/dent.  I am right now doing an 8epi project, but I am using a 4 dent reed as one of the yarns is very soft and one has big bumps in it.  this is not a hard and fast rule, but if it doesnt pull apart, it can usually be used as warp with careful handling.  Knitting yarn can be trickier however, have you thought about yarn designed for weaving?

Good luck

Cheryl

'

laurafry

Is the yarn plied or a singles?   If it is a singles knitting yarn, it isn't necessarily the best choice for weaving.  :((((  The difficulty for new weavers who come to the craft via knitting is that knitting yarns and weaving yarns can be made differently as the two crafts have different requirements in terms of strength and abrasion resistance.  Check the vendors advertising on this site and get some of the yarn samples from them.  Check the projects in magazines/books to see what yarns are recommended.  Eventually you'll gain experience and learn which yarns will give you the results you desire.  :)

cheers,

Laura

 

Ryebaby

 

 

Using a 12 dent reed, because it's the only useable one that the loom has.  So for your project, you have sleyed 2 ends through one dent, am I getting that right? But the dent is a 4 instead of an 8?

 

@ Laura, I can't knit either ;) so I bring no prejudices to my uniformed purchasing! I have come to the same conclusion -- although it looked like a plied yarn, I think it was in truth not. Which even with my limited experience, I'm thinking is a poor choice. I haven't bought any weaving yarn because I think I am not accomplished enough to warrant the expense while I'm learning -- and the choices are all so gorgeous, yet confusing! But I look forward to that part

 

 

Matt (not verified)

I think you found out, though, that it may be worth spending a little extra money on weaving yarn if you don't have to worry about a yarn disaster. I would strongly suggest you start with Perle cotton, it is very smooth and strong, so you can concentrate on learning how to weave rather than dealing with stretchy/fuzzy/weak knitting yarns. Also, purchasing yarn by the cone usually ends up being cheaper overall.

I would recommend purchasing some 3/2 perle cotton, e.g. from Village Spinning and Weaving online (they sell it in smaller "mini cones"). A good sett for plain weave with 3/2 is about 12 ends per inch, so you can just use one end per dent in your reed. Since the yarn is smooth you don't have to worry about putting two ends per dent. 

Hope this helps, once you get going I'm sure you'll have a good time. 

 

matt

Michael White

to clarify-  My project calls for 8 epi.  since the yarn is delicate and has big bumps, I am using a 4 dent reed and sleying 2 threads/dent.  You could use your 12 dent reed and skip every other dent so you could do a project that called for 6 epi.  If you doubled it (2/dent) you could use fine yarn and do 24 epi.  This helps, as reeds are expensive, and you can use them for multiple setts.

Cheryl

Ryebaby

 Well, here's a question for you...what does 3/2 mean? I'm guessing it refers to ply in some way? I was afraid Perle cotton wasn't strong enough, or would abrade too much (I've read other posts about cotton being very prone to fraying). As I mentioned, I only have a 12 dent reed, so that's pretty much what I'll be sticking to! Thanks for the advice, I think I will try Perle next since I can find that everywhere

Michael White

Your 3/2 cotton is sized as follows: A number 1 cotton contains 840 yards and weights 1 pound. What you have is (2) two strands of number 3 cotton. # 3 cotton is 840 x 3 equals 2520/2 (plys)(two #3 threads twisted together) or 1260 yarns per pound. Again using 10/2, 10 x 840= 8400/2= 4200 yards per pounds Hope this helps. 

Depending on the twist and how the yarn is spun perle cotton can be very strong and have very little abrasion.

 Y’all have a good night. Class dismiss. AS Matt said above the WPI (warps per inch) for 3/2 cotton can be 10, 14, 16 & 22 for lace weaves, plain weave & twills.

Michael

http://www.handweaver.us/georgia_yarn_company.htm

Submitted by Ryebaby on