Hi!

I am very excited!  My Sabina CB loom restoration is almost done, and I am going to warp her with carpet warp and weave my very first rug.   I will be using cotton loopers.  I have read that a temple is often used when weaving rugs.  Should I use one or can I weave a decent rug without?  Thanks for your comments~

Candace

Comments

sally orgren

I think you should be able to weave a decent rug without a temple. However, I think your odds are *improved* if you are extremely meticulous at your warping and weaving, getting everything nearly perfect, have planned a short warp (for only a rug or two), and/or you have a lot of weaving experience.

If not, a temple can really help. And using a temple is really not so much about getting perfect selvedges, but keeping the take-up in the width to a minimum so you can pack in the wefts very firmly. And that makes for a longer-lasting rug.

I am thinking cotton loopers are kind of mushy. They may have enough tooth to beat into the carpet warp well and stay put, not spring back slightly before the shed closes. (Hopefully, someone can weigh in who has used that combination of materials before.)

A suggestion—can you borrow a temple from someone in your guild, and try a few inches with, a few without, and see what you think?

Sally

Joanne Hall

Some weavers will get by without a temple if they are weaving a warp faced rug.  That would be about 30 rug warp threads per inch, or even more.  But for most rugs, the temple makes the beating easier, which then makes the weaving go faster.  And if you have any weft stripes, if you don't use a temple, those stripes will smile at you when you take the rug off the loom.

Joanne

celtinbirks

I do have an old temple that came with my loom.  I've never used one before.  Anyone have any tips on how to use one?

Thanks again

steve104c (not verified)

Candace, Do talk to Joanne. There a two types of temples. The wooden ones and the metal ones. The woodens ones are for regular fabric weaving. The teeth are at a lesser angle beause they don't have to go so deep to hold the thinner fabric. Then there are the metal ones where the teeth are angled a lot more so it will grab the thicker(rug) fabric. You do need to get the metal temple if your are going to do rugs. Be very careful because the teeth are very sharp. I make rag rugs(Not really rags, new quilt weight cotton fabric) and I beat the weft in very tight. The temple keeps your selvege from pulling in and making it look like an hour glass. If your going to make rugs, I highly recommend a temple. The sizes very too, so be sure you get the one that is in the best range of widths you'll be working with. It can get expensive if you have to buy an assortment of them. You will be happier with your end product if you go ahead a get a temple(metal for rugs)......Steve.

celtinbirks

Thanks, Steve.  The temple I have is a wood one.  Maybe I should check into a metal one.  Oh, I just checked the prices.  Maybe I'll try the one I have...........

Sara von Tresckow

Do use a proper temple on rugs - otherwise you won't get the firm packing needed to make something of quality.

And YES, good tools are not cheap - but if you're putting in the time and effort, consider doing it nicely.

sally orgren

I too, inherited a wood temple with my new-to-me loom. I started practicing with that.

For what it's worth, I remember Jason Collingwood recommending the thin Swedish metal ones over the wide flat wood ones. Less of your woven area is blocked by this type of temple. After attending one of his workshops, I increased my temple use tremendously, and even purchased a very small metal one for use on my table looms (12-18"). 

A temple IS a good investment, and a good habit to cultivate. I figure if I spend so much time planning, spinning, dyeing, and warping a loom, why not ensure the last step (weaving the warp off) is going to be successful? If I divide the cost of my mini-temple over the number of warps I've used it on so far, I am probably down to $3-5 per use, and over my lifetime, I expect it will be reduced to pennies! ;-)

Sally
(P.S. I am just a weaver. I don't sell weaving equipment or have any relationship to anyone who does.)

jornada (not verified)

Candace,

I was reading up on using a temple for weaving a rug I have just started and saw that you had a Sabina loom.  I don't know what a "CB" loom is.  I purchased a Sabina Sectional loom a couple years ago, which is about 50 years old.  My husband and I cleaned it up, tighten up a few screws and took off weaving.

I was excited to see that someone else had a Sabina.  I haven't seen anyone else mention that type until this evening. (Not that I spent a LOT of time looking at looms on this site or any other.

Would love to see a full picture of your restored loom.

Thanks,

Teresa - Jornada Alpaca Ranch - Ulysses, KS

Joanne Hall

Hi Teresa, 

The loom in your photo looks like a jack loom.  If you send me your email, I can send you a couple files with diagrams which will help you to learn how to determine the type of loom you have.

[email protected]

Joanne Hall

Hi Teresa, 

The loom in your photo looks like a jack loom.  If you send me your email, I can send you a couple files with diagrams which will help you to learn how to determine the type of loom you have.

[email protected]

Submitted by celtinbirks on