I picked up a 22" portable Norwood loom, it is a beautiful loom in very good condition and needed very little clean up.  I got it warped and am frustrated with the harnesses returning to their posotion after I release the foot pedal, they fall back very slowly and can partially raise when the ajoining shafts are raised.  The tracks are all clean and nothing seems to be catching on anything.  The treddle tie ups are small chains and the heddles are wire.  Anyone else have this experience with the Norwood loom or suggestion for what to try??  

Cindy

Comments

Joanne Hall

Hi Cindy,

I would tie a metal rod on the top of each shaft.  Perhaps that is all that is needed.  Jack looms need shafts with weight to make them fall and perhaps yours are just not heavy enough.  You can also try to loosen the tension a little, but then it becomes harder to weave.

Joanne.

Dawn McCarthy

If the shafts were behaving prior to the warp the problem is probably too much tension.  This causes the shafts to float and not have enough room to drop back to position.  Jack looms require that the shafts generate a very slight v in the warp to add tension and allow the shed to rise.  As Joanne suggested, you can also try weighting the shafts.  I own a Norwood and haven't had this issue, there isn't too much the shafts can get caught up on.  I also replaced the chains with texsolv as I found them quicker to tie up.  Good luck!

Dawn

neweaver (not verified)

Thank you for yourt suggestions I tried them and am at a loss for what to try next, I've loosened the tension, taped a metal rod to one shaft without change, looked for warped harnesses, loose screws and it looks beautiful but it continues to lift neighboring shafts,  they seem to lift crookedly, more on the right side than left, they easily fall back when I tap the top of the harnesses but its not a pleasurable weaving experience.  I've manually lifted each shaft singly to see if there is a threading error that might, somehow be pulling up the other shafts with it, I don't see anything and wouldn't think if that was the case they would fall back so easily.  I'm at a loss.  Any other ideas to try?  I also soaped the tracks like you would for a sticky wooden drawer without change, when I manually lift a harness and let go it falls back smoothly and straight as it should.  When I push the treadle the lamms lifit uniformly but don't return to there 'home' position without me pushing on the harnesses or lifting the lamms.   I keep thinking it will be something simple - like when I can't figure out why I don't have a good shed and discover I didn't go over the back beam when I warped!

Cindy

Claudia Segal (not verified)

One thought. Have you tried contacting Norwood? I believe they are still making looms and have a website. Claudia

Joanne Hall

On these small jack looms, the treadle cords need to be vertical.  If the treadle cord is pulling a lamm to the front or the back, it may be the lamms which cause the problem.  I had this problem once with a different brand of workshop loom.

Joanne

Badfaerie (not verified)

I was going to mention the same thing. Check that the lamms are lifting smoothly and aren't binding on each other and that your treadle cords/chains are correct.

Claudia Segal (not verified)

Do you have any photos you can share?  It may be something simple and a picture is worth...

Here is the link for posting photos in your comments or post them in you projects.

Claudia

gailc

Is this an original norwood loom or one that was made by toika?  The original norwoods should be cherry wood.  I have an original norwood workshop loom and have never experienced these problems.

As suggested, some photos would really help.

 

Gail

lkautio (not verified)

What structure are you weaving?  Often block weaves (such as laces, summer and winter, and other tied weaves) have a lot more threads on some shafts than others.  If you are weaving one of these and the tie-down shafts are the ones that are sticking, you need more weight on them.  Or, bungee cording them to something low on the loom can also help.

If that isn't the case, and it is all shafts, in addition to the good suggestions above I'd next check the loom for squareness (see if the diagonals are the same length).  If it is wracked it may be enough to bind the shafts a bit.  Sometimes a high sett (such as for double weave or warp-faced weaves like repp) can also cause problems.

Laurie Autio

oleford (not verified)

I also just bought an older 22" Norwood Loom.  I was wondering about purchasing reeds.  Does it matter if I buy reeds that are 4" in width or should I purchase the 5" width?  Also, do you think there would be any problem with buying the texsolv heddles for it?

I'm new to weaving and am excited to have this loom!

Thanks.

Jan

Su Butler

You might want to check for crossed threads in the heddles...this can cause the problem you are having. Open a shed by lifting one shaft at a time, the check the loom from the side to see if there are threads that are crossed at the heddles. Check each shaft....if all sheds are perfectly clear, then you have a different issue, but if you have crossed threads you can have the problem you are having. Su :-)

SNFLRGL

i know this post is old, but I just joined and saw this post when searching for something so I thought I would weigh in. I'm a fibers student, and while weaving on a 4-shaft floor loom, I had the same issue you described: I would press down the treadle with my foot, but instead of just lifting the designated shaft, others such as the shaft adjacent to it would lift up too, like it was sticking to it. We did not find any crossed warp threads. We checked the tie ups, and we checked the heddles. What solved the problem was this: some of my treadles had three harnesses tied to them. This was too heavy for the loom to lift properly. I needed to use two feet instead so that one treadle had one harness tied up to it and another treadle had two tied up to it, for example. Also, I had to keep the number of heddles even on both sides of each shaft. For example, if there were several more empty heddles on one side of the harness than on the other end of it, the balance was thrown off. This resulted in the harness frame not fully landing back down flush into its spot like it should. After removing some empty heddle hooks and getting that balanced out, the loom functioned perfectly. 

I hope this was helpful! :) 

loomroomcat (not verified)

I have a small Dorset and was having the same problem.  I loosened the screws on the top piece of wood that holds the frame together.  Just a smidge and it corrected my problem.  You might see if there are a couple screws you can do this with that hold the top of the frame in.

Carole M Cole

I would try replacing the heddles with Texsolv. I plan to do that for all 3 of my looms. I had Texsolv heddles back in the 80s when they were new and I loved them. They do take the strain off your warp.

Submitted by Anonymous (not verified) on