Hi

I am restoring a vintage CB loom that has a wooden ratchet and paul advance system in the middle of a sectional warp beam.   The old cherry ratchet and paul are very worn and need replacing.  I would like to use some wood that is stronger than cherry (even though they lasted 66 yrs.)  What wood should I use?  Is there any type of laminated wood or plywood that would be stronger and wear better  than oak or some other type of hardwood?   Any comments appreciated.

GOD bless you!

Candace

Comments

Michael White

Rock maple is much harder then cherry and is used to make a number of looms. Oak is not good at all for a ratchet as it will split along the grain.

Michael

steve104c (not verified)

Candace. Beech would be a great wood for a ratchet. Very hard and tight grained. Also it would be stronger if you sandwich laminate at least two pieces together with grains opposite to each other.....Steve.

Sara von Tresckow

Metal for both parts would be far sturdier.

And it is not Paul, Harry or Dick - it is a PAWL.

celtinbirks

metal for both would be better, but getting someone to make me custom ones might be very expensive and diffucult to find...... like I said, the original cherry ones lasted almost 66 years.

kerstinfroberg

A curiosity: home-made Swedish looms often had used circular saw-blades for ratchets. Some pictures of my cloth beam:

It doesn't quite show on this picture, but it is evident that the tools used for making the hole in the saw blade were not very sophisticated. (The loom must be well over 100 years by now)

Michael White

I have a few old saw blades laying around.

Thanks,

Michael

steve104c (not verified)

Kerstin, That is a really kool idea. Recycling at it's best. Making my wife a small loom and now I know where I might be able to find some ratchets. Old, small saw blades. Thanks for the info...............Steve.

ReedGuy

If you use hickory select wood from a fast grown tree. The reason is you want more closed grain than open (pores) to resist splitting. The early wood (growth in the spring flush) is much more open grained with large pores. This part of the ring is pretty consistant in width from ring to ring. Latewood from summer growth is much denser and pores become small and more dispursed. This is the part of the ring that varies from year to year and site the tree grows on.

Hard maple and beech are better because of the closed grain across the rings. They do have pores, but they are tiny as a pin prick. And if the wood is not dried good, like down to 12% the wheel could warp out of round. This is because of dimensional changes when drying. The shrinkage across the rings is half the rate as the shrinkage in circumference (tangent) of a log. So selecting quarter sawn has an added advantage as the width of the wheel is now across rings and thickness becomes tangent.

Mary Kate

Celtinbirks, did you decide on wood to replace your ratchet? I'm at the same place with an older cherry Norwood. I removed the old ratchet to use as a template, as it is seriously worn and missing some teeth. Would love to hear how your project went.

celtinbirks

Hi Mary Kate,

I never did replace the ratchet and pawl.  The loom was too light duty to weave all the things that I wanted to weave so I sold it not long after I made the post four years ago.  Good luck with yours.  Are you a member of Ravelry?  They have Warped Weavers group where you might find an answer.

Blessings!

Candy

Davie Hannaford Jr

You might also consider using Corian or a polycarbonate plastic 3/8"-1/2"  would hold up.  Corian is a man-made counter top material that can be found in 1/4" and 1/2" thickness.( Note that Corian won't like being leveraged)   Both materials are fairly easy to machine and can stand the test of time if not abused.

Aluminum, brass, and bronze can be machined with woodworking power tools, so long as you remember to make smaller cuts and take your time.

Another option is to face the portion of wood that takes the most abuse with a wear plate of thin brass that is epoxied in place then cleaned up.

Don't know if this helps or not?

Keep us informed.......

ReedGuy

metal fab shop with plasma cutter is what I did for the ratchet. They can cut the fins and the centre very accurately. Small shops where I live won't do little jobs, become too cozy with government contracts. So I was in a  steel worker town and had mine done up in no time and no bla bla bla. ;) My pawl is just galv steel plate with one end bend 90 degrees. Secures beams on a 62" wide weave. :)

jojodbear

leesburg looms have aluminum sets for about $45 shipping included

Mary Kate

Thanks, everyone, for the suggestions. Yes, I have been on the Ravelry sites for Norwoods and DIY repairs. I've learned some good tips there, and found some shared photos of looms of similar vintage, for inspiration!

This loom came to me without a treadle set, so I went to the local woodshop to pick out some cherry to make new treadles. While there, they cut a piece from an 8" (4/4) board so I can try to make replacement cherry ratchet. Only a $4 investment (oh and some new jigsaw blades) to give it a try. Wish me luck!

sandra.eberhar…

I have made them from epoxy impregnated ash, which works well.  If you need finer teeth, a metal ratchet and pawl work better, and they hold a very tight tension better (rug loom).  Plastics do not work.  I have a loom that the previous owner made the ratchet out of high density plastic and the teeth bent.  I had my steel ratchets made at a machine shop that uses water jet technology (cheaper than the plasma or laser machines).  I got two for A$160.  You can download an inexpensive app that will design and print custom gears (ratchets) for you.

ReedGuy

I got two cut for $90 on plasma cutter. 48 teeth per. So which was really cheaper? It just depends on who wants to take it on and how much they feel for taking the time. ;)

There is actually a free online app for such that designs wooden gears by a fellow who has even made 100% wooden clocks, including gears. Plied wood is better than cutting from a board.

http://woodgears.ca

sandra.eberhar…

The gear making program is at

http://woodgears.ca/gear/, as Reed Guy said.  There are other programs out there, but I have found this to work for me.

Reed Guy, the plasma cutting shop wanted $150 each and sent me to the water jet.  Nice you could get a plasma cut cheaper, but that wasn't the case in my neck of the woods.

ReedGuy

Yeah, I understand what you ran into.  But I find a steel worker town usually have more eager folks around. ;) I got it done in my travels as I was going and coming through the same town. Pretty awesome bunch and thanked them kindly. :)

The wood gears site is the one I designed some wooden ratchets. I found the cloth beam one behaved the best, no tear out. But I broke a couple fins on the warp beam one. So I went to metal.

sandra.eberhar…

I have put tremendous pressure on my epoxy ash with no problems, but it's a big gear with big teeth.  One of the advantages of metal is you can get great strength with fine teeth, which makes it easier to adjust.  The big teeth on the barn frame ratchet work because the cloth beam has a winch on it, which is infinately adjustable.

Submitted by celtinbirks on