Hello Weavers.  Every month or so, when I'm feeling like nobody understands a word I'm saying, I come here and fall in love with weaving again.  Thank you.

Question.  Has anyone found an easy way to do some sampling for sett before warping the loom?  I had a problem several years ago when trying to make a set of fluffy bath towels.  After weaving the first few inches, I was completely displeased with the results.  I had to add threads and rewind the whole tangled warp several times before I could make my towels.  They came out nicely but, what a pain!  My daughter is now going to college and has requested a set of "Mom's handwoven bath towels"  Help!  I am was using a cotton yarn (wpi = 40) and cotton for the weft (wpi = 10) and am looking to have a weft emphasized fabric.  Does anyone have a good rule of thumb for using very different yarn types?  Or, does anyone do their sampling without going through the entire warping process first? 

 I want to have fond memories of this project, not have it be overshadowed with frustration.  Any advice would be greatly appreciated.  Thank you, Jenna

Comments

Claudia Segal (not verified)

Hi Jenna,

I have tried winding a short warp using the materials planned and sampling the project.  I weave for 12", cut off the sample and wet finish it to be certain I like the results and then wind the warp for the entire project.  I am about to try doing this on my Structo loom before I embark on a big rug project.  Most of the time, I add an extra 24-30" to my warp calculations and weave a sample before I start the project.  I cut it off the loom and if adjustments are required, I will add warps or re-sley the reed or whatever.  I have never taken an entire warp off the loom and rewound the warp.  If more ends are required, I add a supplemental warp and weight it separately.

Hope that helps.  

Claudia

Joanne Hall

Hi Jenna,

Maybe you could make a warp for four wash cloths.  You could weave the first one, cut it off and wash it.  Then either continue as it is, or change the sett and weave three more, each a little different weft or a different way and then choose the one you like to plan the towel warp.  I do this a lot and I end up with kitchen pot holders to give out as gifts. 

Joanne

jeannine (not verified)

Hi jenna, this is how i learned it in weaving class. first find out the sett by wrapping the yarn round a ruler.Take a small piece of cardboard, indicate a width of 5 cm(2 inch) ,divide in stripes of 1cm(1inch),wind the warp with the sett you want and weave in the weft by hand. this gives you an idea off how the weft and warp will behave. I admit it works only for simple drafts. For this tablerunner i made the sample below and i was pleased with the result.


Bonnie Inouye (not verified)

Jenna, I agree with Joanne, who suggested you could make washcloths as samples.

What kind of loom do you have?  Most weavers would use a floor loom for bath towels, but perhaps yours is different?

I ask because it is hard to understand the problem you described in your first message:

"After weaving the first few inches, I was completely displeased with the results.  I had to add threads and rewind the whole tangled warp several times before I could make my towels.  They came out nicely but, what a pain!" (Jenna)

Why did you have to rewind the whole warp? Is this a rigid heddle loom? 

On a floor loom, you can weave 2 picks of plain weave between reed and heddles, using sticks or heavy yarn, to hold the cross. Then pull the woven part forward and cut it off, leaving tails of warp yarn through the reed. It is easier when you use the same reed with a different number of ends per dent but it is possible to change reeds. In either case, you do not have to unwind the warp- just move those tails of warp yarn into the new places in the reed.

Weavers generally begin with a sett determined by yarn size, yarn fiber, and weave structure, with the sett coming from a formula given by Ashenhurst in his book and repeated many, many times in lots of weaving books and magazines. Now we can also look up yarn size and structure in on-line sett charts for weavers. These setts normally assume you want equal amounts of warp and weft, so you will adjust to get more weft than warp. Why you wish to have more weft? What weave structure will you use? Start by looking up suggested setts so your warp is about the right number of ends, but add something to the width if you think you might need a closer sett. It is a pain to add more wap yarns, yes!

Submitted by Anonymous (not verified) on