I have a warping plan that is written out for 3 colours in tabular format.  The colours are listed vertically on the right hand side of the plan and then the number of threads for each colour are written in the appropriate columns from right to left on the plan.  Where I am confused is where thread counts for 2 different colours appear in the same vertical column.  For example, the 3 colours are Claret Brick and Navy.  The first column shows 2 Claret threads as selvedge, the next column shows 4 claret and 4 navy, the next column shows 4 brick and 4 navy.  How do I interpret this when making up the warp?

Comments

kerstinfroberg

If there wasn't a picture, I would guess it means one end of each - so 2C (selvedge); 4 x (1C, 1N); 4 x (1B, 1N)

Could that be it?

Claudia Segal (not verified)

If the draft is not from a magazine article or a book, you can share it here by scanning it in.  I have been told that drafts are not copyrightable.  In fact, I have been told, there is no such thing as a draft that is new.  All drafts are in the public domain and there is no violation of copyright in sharing them.  

So, please post the draft.  It's an  article or a pattern that are copyrighted and cannot be posted in a public forum such as Weavolution.  Claudia, Weavolution co-founder

Mike (not verified)

Thank you Claudia.  I'm having problems attaching the draft so have emailed you directly with the draft as an attachment.  Regards Mike

 

Claudia Segal (not verified)

Happy to help out Mike.

Have you checked the Help topics?  There is one for posting pictures in comments and it's a YouTUbe video so it takes you through all the steps needed.  

Claudia Segal (not verified)

Okay, check this out from Mike.

Mike, what is the structure of the draft you are using.  I would wind 4 ends of claret and navy together, drop the navy, attach the brick and wind the claret and brick together, drop the brick, attach the navy and wind 4 ends of navy and claret together, etc.  I would read this from right to left.  I take it there are no further instructions on this project.  

Claudia

Mike (not verified)

Claudia

The draft came from the lady with whom I had my first weaving lesson, which was simply an introduction to weaving.  I then acquired my first loom, an 8 shaft table loom, and without the knowledge of how to warp it, the same teacher warped the loom for me with a scarf project, so that I could then practice at home.  Before I completed the project, I was offered the chance to exchange the table loom for a 4 shaft, 6 treadle floor loom, which I accepted with alacrity, losing my scarf project in the process.  So I am now attempting my first warping of a loom and was trying to copy the warping mentioned above.  I think that I have bitten off more than I can chew with a multi-coloured warp and will revert instead to a simpler single coloured warp as my starter.

 

Mike

Claudia Segal (not verified)

The other choice is to wind a warp with 10 red threads and 10 blue threads, 10 green threads, etc.

You might really benefit from Mary Rios' classes on Cyber-Fiber. Her classes might be an easy review for you and a good  way to get your new loom warped and ready to weave.

Check out the classes here.  A webcam and headset with mic will do the trick.

Have you joined the Weaving 101 group?  There may be some past comments there to help you along, too.

TinaHilton (not verified)

I don't see the draft or picture that you tried to include Claudia.

Claudia Segal (not verified)

and decided to clean out my pictures and deleted several items I had included in posts.  So, here is the draft:

I think it's more of a winding draft.  

Thanks for the heads up Tina.

Claudia

Submitted by Anonymous (not verified) on