Hi I'm not into weaving normally but when needs must I'll turn my hands to anything and normally with good results, I think that comes from being an engineer being practical and understanding how things work. The cloth used in my VW camper is no longer available so will need to make some or get some made, looking at the photo it looks a simple pattern with 2x over and 2x under if that makes sense?? My question is what type of loom would I need to make this?? I've seem some floor standing one on ebay but not sure what to look for. http://i191.photobucket.com/albums/z176/sbbfuk/P1010051.jpg Many thanks VWman

Comments

lkautio (not verified)

This is certainly do-able, but there is a learning curve.  It would be a lot cheaper to pay someone to weave it.  On the other hand, if you enjoy the process, you might continue weaving and working out your own designs for other projects.

A 4-shaft (4-harness) loom will allow you to make this cloth. Figure out the cloth width you need, add 20-30% for the weaving width of the loom you need. A floor loom (bigger, with treadles on the floor as opposed to hand levers) is faster and will produce wider cloth.  It can have 4 or 6 treadles for this project. You will need one or two boat or end-feed shuttles, bobbins or pirns, something to wind the warp on (warping board, warping reel, or even chair posts will do).  Get someone who knows something about looms to look at your choice with you.  Not everything on ebay will weave, or weave well.  Some are incomplete, others are damaged, and many are sold by people who know nothing about them.

Beyond the loom you will need some good books - try Debbie Chandler's Learning to Weave, Peggy Ostercamp's Weaving for Beginners, Sigrid Piroch's Magic of Handweaving, or the equivalent.  Don't expect your first effort to produce excellent cloth.  Even with a simple fabric like this one there is a learning curve.  It takes some practice to get good selvages, even beat, even tension, and figure out how to sett the yarns properly. 

Look at your sample and count the number of threads in an inch in each direction.  Subtract about 10% and that will give you the number you are shooting for.  Then you will need to match the fiber and grist (thickness).  A burn test can tell you what the original fiber was.  You can get grist by weighing a piece of yarn very accurately and figuring out the yards per pound.  Multiply the number of threads in an inch by the number of inches you need for width plus about 10%. If your loom does not have this number of heddles you will need to buy some.

Keep asking questions.  There are a ton of things I have not covered.

Laurie Autio

lkautio (not verified)

Forgot to say, your fabric looks like a 2/2 straight twill.  Threading the loom will be simple straight draw (1,2,3,4 repeat).  For treadling you will raise shafts 1+2, 2+3, 3+4, 1+4, repeat.

Laurie Autio

kerstinfroberg

Welcome to the world of weaving!

This is (what I think) I see on your picture:

made into a graph (we call it draft). At the top is a diagram of the threads and their colour order, at the top right is how the treadles are tied up, to the right is the treadling order.

The fact that there are 4 rows at the top indicates that you need (at least) four shafts (the devices that control how the threads go up and down) - and you need four treadles to make the 4 different sheds (the opening where you insert the weft).

This is (in my opinion) most easily achieved on a 4-shaft floor loom.

However, as one of my old weaving teachers used to say, with a frame (to strech the warp) and a stick (to control the up-and-down order) you can weave *anything*, if you have enough patience :-)

In between there is the table loom. Table looms tend to be narrow, but fabric can be pieced...

Um. On another note - you could comission (sp?) someone to weave it for you...

Kerstin (in Sweden)

laurafry

Upholstery needs to be tightly woven.  You'll need to find out what size (grist) of yarn was used, made of which fibre, and most likely use a temple in order to beat the fabric tightly enough.

As Laurie said, there is a learning curve and upholstery is not generally something a new weaver tackles.  That said, if you are game to try, I'd suggest finding some weavers in your area for some hand's on lessons and feedback on the technical info you'll need to proceed.

Like yarn suppliers, equipment to rent or borrow, etc.  Check the resources list here for guild listings in your area.  Or let us know where you are located in case someone is near enough to you and willing to help.

cheers,

Laura

VWman (not verified)

Just like to thank you for your comments, I think I understand what was said but as with all new things it's a lot to take in. I'm open to all option at this stage and may even get some quotes to have this made As for location i'm near Bristol UK

laurafry

I was going to give you a referral to a weaver but she's in the US.  :}

Have fun with your re-fit.

Cheers,

Laura

lkautio (not verified)

You can find a list of UK weaving guilds here, along with classes:

http://www.wsd.org.uk/

Look on the guilds tab to find a location near you.

Have fun!

Laurie Autio (daughter of a mechanical engineer...)

Submitted by Anonymous (not verified) on