I have a warp on the loom (180 threads), beamed, threaded and tied on the front.  I started weaving in some junk to spread the warp and I am popping black threads like crazy.  The yarn is 10/2 cotton and the black is older than I thought.  I lost a couple threads in beaming and decided to move on.  Now I am in a real pickle.  

Half the warp is medium gray and the other half is black (uneven stripes of each) threaded in a alternating twill and basketweave.  The camera battery is charging for me to take pictures

Before I cut it off and start all over I am looking for advice, suggestions, ideas.  I have 10/2 cotton in two other shades of gray and was thinking about adding a supplemental warp with the grays replacing the black.  This is only the second warp on my new-to-me Glimakra Standard.  Not sure how to replace the black threads and weight a supplemental warp.

TIA for any ideas.
Claudia 

Comments

Sara von Tresckow

Old black cotton is subject to deterioration.

To do a supplemental, make a small chain with the correct number ofthreads, bring them through heddles and reed where needed, and weight UNDERR the lease sticks off the back beam with anything that works - washers, small tools, c-clamps, etc. You'll be surprised how little it takes. You might even get some fresh black and use that.

Joanne Hall

Hi Claudia,

How unfortunate to have this happen.  I had some mill end black cotton that was very weak, so I just discarded it.  It is always a disappointment to get something with this poor quality.  I heard onece that one of the reasons for dark colors to be weak is that dark colors can be made by overdyeing other colors.  Perhaps that can make them weaker.

I have been waiting for someone to answer you.  I am busy teaching this week.  Sara has a good idea, especially if your warp is long.  If it is a short warp, you can wind it forward on your cloth beam with sticks and insert your new warp ends onto the tie-on bar and then re-beam.  I don't have 10/2 cotton, but I have good 8/2 black cotton, long staple and very strong.  Joanne

sequel (not verified)

Whew!  I feel better already.  One of my students was using an 8/2 black cotton and it broke time and time again.  I knew that black dye was more likely to weaken fibers, but this was my first experience with the tragic results.  Afterwards she asked me if we should save the rest of the cone for weft.  I gave her the dubious honor of dropping the whole cone into the trash.

jordanj (not verified)

All of my ideas have already been presented by Joanne and Sara, so I have nothing to add but sympathy. Good luck and let us know how it turns out!

Jennifer

sally orgren

I think we just hit on this same topic over at Weave Fail. (The offender in my case was a cone of 16/2 black.) I gutted it out, whining all the way through 5 or 6 yards, and then my guild mate practically forced me to throw out the cone. (It was good advice.)

claudia (not verified)

Well, I can't gut it out.  I loosened the tension, fixed 6 threads, advanced the warp a touch and then added just enough tension to weave, not a lot, and lost 5 more threads.  

Last night, I wound a warp of 8/2 cotton that is very strong, I checked several times.  It's black and light blue.  Since I am changing size of yarn I need to change reeds, my previous sett was 24 and I need to change to 20 unless I want a rigid scarf.

Here is my plan (comments, please).  I am going to cut the current warp in front of the beater and tie into bundles.  Then, I am going to tie on the new warp and wind it through the current threading, insert the lease sticks once all the knots are through.  Beam the new warp on top of the old one and then re-sley a larger reed for 20 epi.  

I tried to wind the warp forward as Joanne suggested and more threads started breaking.  I thought it best to take the current lease sticks off the top of the back beam and just leave the faulty warp as a dummy warp since that's what it is, truly.

Claudia

jordanj (not verified)

Sounds like a good plan, but after the new threads are through the reed, heddles and lease sticks, I would cut them from the old warp, leave the new threads "hanging securely" and then unwind and remove the old warp. Then once that old warp is gone, tie the new warp onto the back beam and wind away, just as if you had warped F2B. 

That is just my opinion and others who are more knowledgeable might have better ideas.

Jennifer

claudia (not verified)

Jennifer,

 

Good thinking.  I just came back upstairs from starting the tying process and had decided to do exactly as you suggest.  I want rid of the old warp and I risk more breakage with the new warp tied on. 

Thanks, 

Claudia

sally orgren

Well, if this helps, what my guild mate said that finally convinced me to pitch the cone is that if the warp was breaking so badly when just beginning weaving, how long would the piece woven with weak thread last?

So it's wise to take the time now, replace and discard the weak warp. (even if it's a grumbly process until you finally have it tensioned.) Listen to a good book on CD and I'll bet you'll be done before you know it!

Submitted by Anonymous (not verified) on