I took a class this past February and learned to weave on a Dorothy 24" table loom.  Shortly thereafter, I purchased a used Leclerc Fanny floor loom, 36", which has a sectional beam.  After doing research on the Internet, I've discovered that the sectional beam is suitable for rag rugs, among other things, but requires tensioners, counters, etc.  (I'd rather spend the money for the extra equipment for the beam on yarn.)  I'm weaving towels, placemats, and such and find the sectional beam to be a pain in the neck.  Should I (or can I) take the sectional equipment off the beam?  Or should I spend less money on dividers and guides?  The picture shows a rag rug warp that was on the loom when I bougth it.  Any comments/suggestions would be appreciated.

Monica Bellas

Comments

Sara von Tresckow

 Plain beam warping can even be done with the sectional equipment in place - just be careful that ends don't snag on the dividers.

If you like to weave finer fabrics, by all means remove the sectional rakes and use a warping mill. Some years back I did some figuring and what I spent on a 4 meter warping mill was about what I'd need for tensioners, spools, spool rack, etc. I've never regretted going with plain beam warping as I usually start at 30 epi and work up from there. That would be a heck of a lot of winding - as it is I usually warp with two threads form 2 cones. 

sally orgren

I have been weaving long enough to know I am not the most experienced person with sectional warping, as I tend to prefer plain beam. I only do a few sectional warps a year. Most of my weaving is finer setts, suitable for garments, scarves, and household goods, but not so much rugs.

What I have noticed is that sectional warping tends to result in a lot of loom waste.

Rugs, I usually don't care. But if it is precious material and a shorter warp, I certainly would rather use the plain beam and have the warp get as close to the castle as possible when I am near the end of weaving.

tien (not verified)

How does sectional warping produce loom waste?  If you make the tie-on strings long enough, you should be able to weave right up to the heddles (at least, I can).

Fine warps - the AVL Warping Wheel is a godsend.  It's what I use for sectional warping, and it is really quick work since you can wind directly from multiple cones - no spool-winding!  I used it for a 20-yard warp sett at 96 epi and it works like a dream.  If you are sectional warping with fine yarns I really recommend the warping wheel.

All that said - if you'd rather spend your money on yarn than on sectional warping stuff, go ahead and warp just as you would on a plain beam!  But I would use a trapeze for beaming on, it will save you a LOT of time.  Kati Meek's book Warp with a Trapeze and Dance with your Loom has been reprinted and I can't recommend it enough - has plans for a trapeze if you don't already have one.

Cheers,

Tien

 

Sara von Tresckow

 Sectional warping without the warping wheel does produce waste.

When winding all those spools, even using a yardage counter, there is slippage and stretching that, in the end, leaves odd amounts of warp on the spools. For rugs at 10 or 12 epi, not a problem. For expensive warp material at 60epi, it is costly. Also, it it turns out that if even one section is a bit shorter than the rest, there is waste in all the others.

Monica Bellas (not verified)

Thanks so much for all of the input.  I have been plain beaming (I didn't know it was called that!) and fighting the threads getting caught on the rakes.  Thus my tension hasn't been so hot, but hey! I'm still learning.  I don't have a lot of loom waste, as the tie on loops go right up to the heddles.  I will continue to ponder this; more comments are appreciated!

Thanks,

Monica

Diane Roeder (not verified)

Without an AVL warping wheel, sectional beaming is a pain.  With one it's great.  But the AVL warping wheel is expensive and it's an awkward, gangly thing.  I still love it though.

Diane

thelmaweaves

I agree, the AVL warping wheel is the best way to do sectional warping.  I have no loom waste and my warping goes very fast.  Yes, it is big and gangly, but a wonderful invention! I wouldn't be without it!

Sharon

crosstownshuttler (not verified)

 Hi Monica,

I don't have anything new to add to the "to sectional warp or not" discussion but I'm pretty sure you can remove the sectional rakes (my term, I can't think of the correct one) and use the plain beam. My LeClerc Artisat has removable rakes. Just unscrew the three screws in each section. You may need a square-head screw driver.

I hope this helps.

Carie

Monica Bellas (not verified)

Carie --

Thanks!  I actually removed all four of the sectional beams, but now have run into another dilemma.  (I apologize in advance if this is a dumb question.)  How do I attach the beam stick to the warp beam?  I'd prefer not to use a cloth apron.  I'm sure there's a way to lash the beam stick, but I'm not sure how to do it.  (I wasn't a Girl Scout.)  Are there pictures on the Internet that someone can direct me to?

Thanks again!

Monica

laurafry

Sectional beaming is appropriate in certain circumstances and a god send if one is doing production weaving.  Not so much for short, narrow warps, where I just wind a warp chain as usual and beam it using tension, preferably with a warping valet/trapeze, then thread my heddles, sley the reed and start weaving.  I have a 'slide show' on my website showing how I dress my AVL with 1" sectional rakes with a painted warp chain. 

When in doubt about a tool or technique try to borrow the equipment and see if it is a good match for you or not.  The really nice thing about weaving is that it has evolved over so many millenia in so many different cultures and levels of technology that there are lots of choices for people to try.  :)

Cheers,

Laura

Monica Bellas (not verified)

Thanks for the tip, Laura.  I'll take a look at your website when my brain isn't quite so fuzzy.

PriscillaE

 

I have a new Cranbrook with sectional warping beam and a new AVL Warping Wheel (Both Wonderful!!). My first project was a baby blanket. The sett in the reed was 12 and the ends per inch in the sectional warp beam were 18, so I never thought about what you do when you have a bigger discrepancy between your sett and the threads that fill each section of the beam (mine are 2" spaced pegs).

 

So... here's my question (I've searched and searched and no one seems to address this):

 

If the sections between the pegs are supposed to be fully filled to where they are perfectly flat layers (I've read that is the RULE), don't you have to figure your Wraps Per Inch (whether it be 60/2 silk or 8/5 linen for a rug) to fill those sections?

 

If so, what do you do when the width in the sectional warping beam and the reed are quite different? 

 

Example:   My warp-faced rug is only going to have 8 epi in the reed, but to fill the 2" sections on the sectional warping beam I figure I need to have 28 ends of 8/5 linen in each to make each section level (the space between the pegs is actually 1 3/4" and wrapping around a ruler gave me 28 ends).

 

The width in the reed is 24 1/4" and the width in the sectional warping beam would be 14". That can't be right. My tension would be greater at the edges versus the center.

 

Peggy Osterkamp has a chapter on Sectional Beaming but does not address this issue, although she does say, "Remember, it's ideal for a warp to be wider on the warp beam than in the reed..."

 

It sure seems like this information should be SOMEWHERE. I just haven't been able to find it. Any suggestions?

 

Priscilla E.

 

mneligh

Flat is relative -- you don't want extra build up in some spots of a section and not in others.  What you really want to avoid is a partly filled section.

When facing a situation where you're not filling a section entirely, use a paper strip or the like between layers.  I use old business cards.  I put mine in in kind of a spiral, and I reuse them.  That said, regardless of the thickness of the warp threads, I would be concerned about a sett so open that you have gaps in sections, or where the width on the beam is not close to the width at the reed.   

I don't follow your logic above about your epi, width in the reed, etc.  If you have 2" sections and 8 epi, you need 16 threads per section.  I do have to confess that I haven't read Osterkamp's book -- I learned from an old Robin & Russ pamphlet titled something like "Sectional Warping Made Easy" that I got about 1979-80.  I've been warping the same way since then until Tien wrote about the AVL warping wheel and converted me.  

 

ReedGuy

With a sectional beam that has the SS hoops, your losing probably an 1/8" between sections. The hoops are probably installed in holes drilled at exactly each 2" in width, so a 1/16" is lost either side of the 2" mark, double that for the 1/8" loss. If they are dowel wood, then the dowels are probably 1/4", so you get 1-3/4" as you stated. Same problem arises, but 1/8" this time either side of the 2" marks when installed. No revelation there I guess.

I would work out the sett required on the sectional to fill each section and to match closely the width of your woven fabric. If your a little wider on your sectional by a couple inches either way, it's not a big deal. Make use of lease sticks as well. It never has been any trouble for me anyway, and fine cloth results just the same. I made my sectionals so that I have a full one inch in each section. But anyway, you basically think of sett on the beam as well as sett in the reed that will match your cloth width. At least I do. I beleive if your doing very long warps, you need something to be placed every so many layers. Making sure each section is perfectly filled across the width isn't going to negate this practice. Because regardless, once you have lots of wrappings around the beam, one wrap or another is bound to pull through layers below. This is why manufactures made those pieces to be placed every so many layers, or why would they bother?

PriscillaE

Robin and Russ say to make the sections "as flat as possible" and they have some examples, but they don't explain what to do when your sett in the reed does not provide enough threads to make the sections in the warp beam "as flat as possible." AVL's YouTube video on the Warping Wheel says to make smooth flat layers. They say, "It is very important that the bout rolls on in nice flat layers, filling the section completely from side to side." But they don't address how to come up with that thread count. I figured it was best done by Wraps Per Inch. Laura Fry has written on her Blog, "When the warp is beamed tightly enough the threads cannot cut down into the lower layers." I'm hoping she will chime in here at some point to talk about how she figures the number of threads in a section. I'm also hoping Tien will tell how she calculates her fine threads for each section vs. her sett in the reed. How would she calculate threads per section for a weft-faced rug at 4 epi doubled, such as Tom Knisely's weft-faced twill published by Interweave Press? I guess I could pack each section with business cards or such, but I'm really curious to find out if there is a formula that goes along with this rule that the layers be completely flat. I would include a photo of the page in Peggy's book where she talks about keeping your layers perfectly flat and has a diagram, but I'm afraid that would probably be some kind of copyright infringement. I should probably write to her too about this. Priscilla

Diane Irvine (not verified)

Priscilla,

The number of threads in a section is your sett. If you have 1 inch sections, and your EPI is 22, you will have 22 ends in each section. If you have 2 inch sections, you will have 44 ends in each section.

Calculating your EPI is the same as for regular warping. It depends on the yarn you use, and your weave structure. 

There are different ways of making sure the section you are winding is the same width as the section, thus ensuring it winds on in flat layers. Look at your tension box. Does it have removable reeds, or does it have one reed that pivots?

If you have a removable reed, you are supposed to choose a reed that is appropriate to your desired sett. So if you need 22 ends in a 1 inch section (for example), and you have a 6 dent reed for your tension box, you could thead you thread 3-4-4.

If your reed pivots, then simply thread in any regular pattern (so like 1-2 ends per dent) as long the result is at least as wide as your section. then simply pivot pivot the reed to narrow the ribbon of yarn coming out of it. 

 

PriscillaE

That all makes perfect sense (and the warping wheel has a reed that pivots) except that my sett with the weft-faced rug is 4 working ends per inch doubled (thus 8 ends per inch) of 8/5 linen. Back at the sectional beam, that means 16 ends in my 2" section. This does not fill the section and thus the layers as I wind on are falling into lower layers. For my short rug, this will most likely be ok, but not for very long warps. Is this a case of a weft-faced rug being the exception? I think I probably need to get out several yarns of differing thicknesses and check to see how many threads it takes to fill a 2" section.

Diane Irvine (not verified)

Priscilla, you'd have this problem whether you warped sectionally or not. Even on a plain beam, the various layers would digg into each other. This creates tension problems on long warps, even if you beam under a lot of tension.

On plain beams, some people use sticks or paper between layers.

You may be able to do something similar on your sectional beam. For example, LeClerc sells "sectional dividers" which are basically little sticks that fit between the metal loops. For that to work, you have to place them in the same spots in every section.

canaanmohair

I am going through a huge family crisis but have a commission to do.  I can't remember the calculations for the counter.  I need 30 yard warp sett at 30 epi.  By my calculations the counter has to say 300 for this to happen.  I also forget when the yarn goes through the catch hook.  Please help  Thanks

Bonnie Inouye (not verified)

The AVL website has instructions and videos about the warping wheel and other products.

www.avlusa.com 

My latest warp used 3 cones of yarn. How many cones are you using? It is faster with more than 1 cone, but of course you can measure each warp yarn one at a time. The wheel is usually set up for 3 yards per turn of the wheel but there are other ways to arrange the pegs or spools (depending on which model you have). If you have 3 yards per turn, then 10 turns will give you 30 yards. Do you have one-inch sections or two-inch sections. Check what you have and then read or watch the information given for the AVL warping wheel. It is tough to face a 3-yard commission at a bad time, so maybe you could ask them for an extension on the deadline.

Guiding Myth (not verified)

The instructions to keep the section flat means that as you put the threads on the beam they go on flat and do not mound up.  You put them on in one layer edge to edge.  It is possible to put in the layers flat no matter what the sett is.  

Your questions is a "trick" question :)!!  You use the sett to determine the number of ends per section as many people responded above.  

Making the warp flat in the section is technique or a method you will have to understand and learn.  Have someone show you or if that's not possible watch videos.  It is not intuitive. It is done by manipulating the reed angle - which adjusts the angle that the thread winds on the beam.  The angle is adjusted so the width of the group of warp threads narrows or widens.  The width should be adjusted so it is equal to exactly the width of the section - so that the warp winds on just touching the dividers. If you can put each layer on edge to edge it will be flat.  If you make the angle too wide it will look like a smile.  If the angle is too narrow it will look like a frown. If it is just right it will look flat ____.  Even if you have just 10 threads in the section.  Really.

Good Luck!

Stephanie S

mneligh

One of the reasons many people weave is to be creative, and weavers need to be creative problem solvers.  

I have 2 hybrid techniques I use to sectionally warp my Macomber, which in its current location does not have enough clearnace behind it to fit the spool rack and the tension box.  Both involve the use of a tension box.

In the first method, make a chained warp for each 2" section.  If weaving at 22 epi, put 44 ends in each chain, and crank on each section individually.  My Macomber tension box would require rethreading each time, which is a pain, so I have gotten a LeClerc tension box with reeds at both ends, not holes in a board.  On wide warps, this speeds things up significantly.

However, AVL warping wheels are wonderous things.  Even though I cannot quite get the reed of mine lined up to produce a perfectly flat wind-on (due to the angle at which I have to turn my loom and the wheel to get everything to fit), I find that if I use either tension box (the Macomber slides better and is more compact) between the loom and the wheel, I can correct the angle problem and get a nice flat section.

sandra.eberhar…

I have read several people talk about epi in the reed and  how that relates to ends per section, but I do not see the relationship.  You need ther right number of ends in the section to form a flat ribbon to fill the section, regardless of what it will be sleyed at.

NancyHassel

I use my AVL warping wheel set to 3 yards per revolution.  When I warp 30 ends x 30 yards each = 30 ends x 10 revolutions = counter reading of 300 upon completion.  I would check after completing each end to ensure the counter showed an increment of 10. 

I just wound a warp with a warping paddle and 4 cones => 4 ends at a time and it was much faster.  This technique is described on Tien Chiu's website - http://www.tienchiu.com/how-tos/equipment/tips-for-using-the-avl-warpin…

PriscillaE

Well, yes and no.  The bably blanket I did was fine doing it that way.   It is different when you are warping a weft-faced rug with 8/5 linen at 4 doubled ends per inch, needing it to be 28" wide in the reed. You have to figure your ends per section so that the width on the sectional warping beam is close to the width in the reed. I had only 16 ends in a 2" section. What I did was on the first turn of the beam, I kept the ends together and flat on one side of the 2" section. As I came around the beam, when I reached that first section, I filled the other side flat. On subsequent turns I just made sure that the threads were spread out and flat. The warp was only 5 yards long. I don't think you'd run into trouble with a longer warp, but I haven't tried that yet.

When I wrote to AVL last year regarding this subject, this is what Amanda sent. (She gave permission for me to share this with Weavolution)

Priscilla

 

How many ends per section?

In general, you would just take the ends per inch (EPI) that you plan to use in the reed times the size of the section in inches. For example: A set of 24 epi in a two inch section would require 48 ends per section.

One problem is sometimes the total number of ends you need for a particular project does not divide equally by the desired EPI.

Say you need 300 ends sett at 24 epi which provides a warp 12 1⁄2 inches wide; (or 6, 2-inch sections + 12 extra ends). In this case you would divide the total number of ends by the closest number of sections, in this case 6 sections. So, 300 ends divided by 6 sections gives you 50 ends per section. The warp will be 12 inches wide on the beam and 12-1/2 inches wide in the reed, this small difference will not cause any problems during the weaving process and works just as well if the warp is slightly wider on the beam.

Another issue when doing sectional warping is a very open sett. We do want to create flat even layers, but 6 or 8 epi doesn’t provide enough ends to fill the section with a solid flat layer.

In this case, it will be necessary to create the layer from two or three revolutions of the warp beam. Roll the bout on tightly and at the full width of the section, the ends will settle into the spaces below in an orderly way and make the flat layers over a few revolutions.

A very dense sett doesn’t seem to present many problems, just be sure to keep the layers flat with no build-up at the sides of the section.

General Rules for Sectional Warping:

All sections must have the same number of ends of the same yarn size – i.e., the circumference of each section must be identical.

Wind on with at least as much tension as will be used when weaving off the warp. When in doubt, tighter is always better!

The number of ends per section does not have to be the same as the sett in the reed, but should be within about + or - 10%. 

mneligh

Are you really worried not about "normal" cases, but extreme situations where the ends in a section overfill (warp-faced or multiple layer) or underfill (weft-faced or some lace) that section, preventing the threads in that section to lie flat?

Generally, that does not happen, although it's possible.  In those cases it would be wise to put something between the layers.

rosbif

Hi , first time here , im wondering if anyone knows what mark my loom is , its not a leclerc as i inquired of them and they said no.And does it have a sectional beam , i dont really know what that means for me as a new weaver , and does anyone know what this is  Thanks

Ps i am in France if that helps.

SusanBH

Rosbif,

You might want to start a new thread for your loom question, rather than replying to this thread.  I happened to see your post because I was curious about sectional warping, otherwise I would have missed it.  And sorry, I don't know what kind of loom that is.

cvweaver (not verified)

I prefer to warp back to front. I want to do a long warp. I have an AVL warping wheel. I recently got a Baby Wolf loom that has a plain warping beam. (My other looms are sectional). My only thought is to tie leaders on to the apron rod. Would this work? Do you have other suggestions? I want to do a long warp of 10/2 cotton, set about 24 epi and maybe 11-12 yards.
Submitted by Anonymous (not verified) on