I have tried several different ways of tying on to the front apron, including shoelaces (from Nadine Sanders' book) and lashing on.  Currently I'm trying the "lashing on" method again.  I'm using braided chalk line (minus the chalk of course).  I remember someone recommending it and it does seem slippery.  My current project is a baby blanket that's 40" in the reed and for some reason I'm having trouble getting even tension on the bouts.  Can anyone offer any advice on the best way to do this?  I just keep tugging on the cord so the slack moves, but I wondered if there was a better way.

What's funny is that I wove one blanket with no problems at all, but discovered a threading error.  I cut off that blanket and fixed the error but now can't seem to get the tension even again.

Comments

lkautio (not verified)

Wider is definitely harder with lashing on.  I open a plain weave shed and lash the knotted bundles through the open shed with the lashing cord held under tension.  Then I poke each knot hard with open shed from right to left.  Tighten a click and poke each knot (with open shed) from left to right.  Continue tightening and poking from alternate sides until it is even.  Sometimes I have started with a loose warp, open shed, and a dowel to press evenly across the width to get a roughly even starting point.  Tugging with your fingers is hard to get even results.  I think I learned this method from a class with Peggy Ostercamp.

Laurie Autio

sally orgren

Here are the details for my method and trouble shooting:

I try to knot the bouts an even distance from the reed, (starting in the middle and working alternate sides) but don't obsess about this. For lashing those bouts, I also start in the middle, lashing toward each selvedge. I keep my bouts small, maybe 2", especially if I am going full width.

When lashed, I don't fully tighten the warp, but use fairly moderate tension, and then I work the treadles. A bunch! All kinds of combinations. I want the warp to "tension itself" as much as possible and let the lashing cord do the work.

When I think I am ready, I tighten the tension fully.

Then I throw 3 pics of cotton "undershirt" or t-shirt strips. Something soft. I don't beat between these 3 pics. When I have three, then I beat and if there is any differential tension between bouts, it pulls it to the front of the knots. I usually continue for at least an inch or two before I start weaving with the actual weft. (My front loom waste is typically 5-7" with this method.)

If there is still a tension differential after a bit of weaving, then I remove the packing weft, and start adjusting the lashing cord to tighten the slack bouts and spread that extra slack over many bouts. I check progress by "patting" the warp, not just between the apron and the reed, but also going around to check the warp tension between the castle and the back beam too. (However, most of the time this isn't necessary.) 

At this point, my knots may no longer be in alignment with each other, but that is okay, as the soft-t-shirt material takes up the difference and what is more important is that everything from the weaving point toward the castle is evenly tensioned. It is important to pay attention to the "fell" line (the place where the weaving starts) and make sure it is parallel to the reed at all points along the width. 

If I discover I have a threading or sleying error: 
I release the tension quite a bit.

I clip clothes-pins to hold the lashed bout string to the rod, on either side of the bout, so the lashing string will not move. I untie the problem bout and correct the issue.

To reattach, I split the bout into two sections and tie a double knot with the lashing cord captured in the center of this double knot. With the clothes pins on either side, they hold the lashing cord in a loop, just where you left it. And it can still slip around inside the bout if it needs to readjust.

When done, I release the clothes pins.

Retreadle a bit, retension, and re-throw the 3 pics of stuffing, etc.

------
I lash to the front apron with carpenter's "chalk string" too! I like that it is slippery, but holds a knot when needed.

(Credit goes to my guild mates for teaching me all kinds of warping tricks I have shared above!)

weaver-dyer (not verified)

 Lots of great tips for tieing-on and tensioning the warp.  Another method of tieing-on and tensioning is the Nyquist method developed by Janet Nyquist.  A description can be found at:  http://www.weavingworld.ca/tips.htm#dr  Scroll down to find the Nyquist tie-on.  

Janet 

 

TinaHilton (not verified)

My bouts are are just under an inch, but I ran the cord through the center of the bout.  I like the idea of taking it through the plain weave like you do, Laurie, and will try it next time. 

This warp is on my AVL loom, with the live weight tension, so I can't tighten it as I go along Sally.  But doing a lot of treadling to even out the tension does sound good.

Nadine Sander's method using shoestrings is (I believe) based on the Nyquist, now that I read it again.  That does work well, but I like to try different methods to make sure I've picked the one that works best for me (or for the yarn I'm using).

These are all great tips and I really appreciate them.

Thanks!

kerstinfroberg

Sally wrote:
"Then I throw 3 pics of cotton "undershirt" or t-shirt strips. Something soft. I don't beat between these 3 pics. When I have three, then I beat and if there is any differential tension between bouts, it pulls it to the front of the knots. "

I heartily agree - except: I prefer something stiffer! (no accounts for taste?)

 

 

 

sally orgren

Okay, now I have to try something stiffer instead of raiding the DH's undershirt drawer.
(He'll appreciate it.)

I don't think we ever stop refining our warping technique, do we?

Submitted by Anonymous (not verified) on