Does anyone know how to rescue a rusted reed? I bought a used Glimakra loom and the reed is pretty rusted. I want to try to save this reed. I'm going to get a new stainless reed but would like to have an extra reed in a different dent. Is there hope or do I need to toss it?............Steve

Comments

Karren K. Brito

I have never managed to recsue a rusted reed.  I've used naval jelly , wire brushes, sand paper and lotsa elbow grease and there is always still rust inside the dents.  I've been tempted to take it to place that has a pit of rust remover and have it dipped, but I haven't yet.

Sara von Tresckow

 If it isn't pitted, you can clean some rust off by simply weaving a stretch with something like wool with spinning oil in it - the rust comes off on the warp.

Otherwise, I'll second Karren - if you get a really good deal on a used loom, show your appreciation by getting nice clean, new reeds to go with it. You will still have saved a bundle.

ingamarie

I read in a newsletter recently about using vinegar to clean a reed, I can't find that but googled it and found this at http://www.lasaranas.org/weaving_tips_and_tricks.htm  which I think is pretty much the same advice. Seems like you'd need to be careful not to mess up the tape on the edges of the reed, and I haven't tried it. But if you're going to trash the reed anyway it might be worth experimenting.. and um, let us know how it goes :)

marie

 

"Use old rags that you can throw out when you’re done (the rust won’t come out in the wash). Saturate the rags in white vinegar, wring out and place them along the length of your rusty, nasty reed. Then wrap up the whole thing in plastic and leave it for 24 hours. Remove the plastic and rub the rust off with one of the rags. Now rub the reed with a completely dry cloth and use a hair dryer to completely dry everything. This works like a miracle!"

Michael White

Steve, Make a paste using the juice of one lemon, a cup of white distilled vinegar and Borax power to make a paste. Apply the paste and let stand for 30 minutes then rub off with a puddy knife, rugs, steel wool. Wipe down with plain white distilled vinegar. For more grit you could add some fine sand. On some reeds the tape is paper and will have to be replaced. Somewhere there is a whole discussion on replaceing tapes. Duct tape now comes in lots of colors. After the reed is dry spray with a rust preventive like "Blast 50" which goes on wet but dries to a dry film.

Let me know how this works? Like Karren and Sara has stated if your reed is badly pitted you maybe looking at buying a new reed.

Michael

steve104c (not verified)

Michael, Thanks again for the info. on the Glimakra loom. I'm refinishing it right now and will probably have it finished in a few days. I'm really excited to begin making rugs on it.Thanks............Steve

TNWEAVE (not verified)

Don't know if this works, never tryed it, but I have been told that if you soak it overnight in a bath of coke, you can get the rust off.

tien (not verified)

Coke is basically a dilute phosphoric acid bath (with carbon dioxide bubbles to help lift particles away) - it should work about as well as vinegar.  I had an ex once who used to use it for cleaning (some) geological specimens, especially in the field - he was a Diet Coke addict so always had plenty of it around!

debmcclintock

I used to keep a large gallon bottle of Coke in my car that I used to clean off my auto battery to get back and forth from work, until I could afford to replace my battery, ahhhhh those were the days!

isis01 (not verified)

I sandblasted my reed and replaced the loose covering with duct tape.  Then just something coarse and a bit mottled.  It worked like a charm and very quick.  The other methods are interesting.  I know about the Coke to keep the battery posts clean.  I keep a penny there too (close to the posts.)  It corrodes first.  Coke will also clean oily film off your windshield.  Now I am off to try it on the reed.

Michael White

Coke will work on light rust, you will have to wash it well to remove all the sugar.

Michael

Michael White

Steve,

I forgot to add. You need to rap the reed in plastic to keep it from drying out. You can then scrub with a nail brush or a vegy brush to work the soften rust off the reed.

Michael

flamingo (not verified)

I bought a soft cotton buffing pad for my drill. It has layers of cloth stacked about 1/2" thick. The diameter is maybe 6". I just attach it to the drill and rev it up and run it until the reed is clean. The layers fit in the dents and clean the surface rust very well. This can take several minutes (depending on the width of the reed and how bad the rust is. I found it works great, although my reeds did not have pitting on them.

Michael White

Thanks, I will check this out at the HD>

Michael

Submitted by Anonymous (not verified) on