I have a sort of checklist I go through when I finish threading the loom and get ready to start weaving but I realized the other day it would be great to have a checklist of every step from deciding what yarn, designing a draft or picking one out, etc.  For instance, I often forget to open a plain weave shed when beaming the warp if I am warping b2f.  It would be great to have a checklist for the entire process.

Does anyone have one they would be willing to share?  We might be able to add it to the Resources section along with the Weaving and sett calculators. 

John Stewart, of Daily Show fame, had a surgeon on a couple weeks ago who wrote a book about reducing infections and death by following a simple checklist before and during any surgery.  He was very impressive and I am sure there are lots of disciplines that use them, why not weaving.  The book is titled "The Checklist Manifesto" by Atul Gawande, if you are interested in the original source.

Perhaps we can create the list right here.

Claudia

Comments

tommye scanlin

 Claudia,

I have one that I developed for my university students.  It's pretty lengthy and describes warping back to front.  I can share it with you later (am out of town right now).

Tommye

lkautio (not verified)

To a high degree such a list would depend on the warping method, the loom, the weaver's design process, and the weaver's technical skills.  One universal list would not do the trick.  For example, for me designing the draft is 95+% of the time involved in the process, yet there is no simple set of steps that I could give someone on designing that wouldn't have to be based on an understanding of their level, their aesthetic, their equipment, and their technical preferences.  Warping back to front on a small loom may allow different tactics than warping back to front on a large/deep loom.  Threading heddles on a 32S loom (or 16S) may be aided by some steps that are totally unnecessary on a 4S loom.  Culturally, warping in a traditional Swedish manner with Swedish style equipment, is different (for very specific reasons) from some of the common US warping techniques on small folding jack looms. 

Anyway, if someone posts a list, it would be helpful to know something about their equipment.

Laurie Autio

Ellen (not verified)

The photos I posted on flikr and gave a link to here some time ago more or less covers my method. It does not include the designing and calculating before making the warp, and I also deliberately left out the tie-up part, because as Ikautio mentioned these can be very different to what a lot of people here are doing (mine is a large countermarch loom, and I suppose I am doing a very Scandinavian thing?!)

The post was called something like an ABC of warping, if you want to have a look again. I added little explanations to most of the photos.

www.flickr.com/photos/dybvad/sets/72157623267479594

(Hope this link works)

Sara von Tresckow

 The best "checklist" is

1. A decent understanding of the process that is going to take place and materials/setup needed to complete the process successfully

2. A review of each step in that process, at a point where corrections can be made most easily

Don't wait until the warp is tied on to check threading and sleying.

3. Utilizing the warp space usually taken up by toilet paper, cardboard and such as the place to test the fabric for any flaws or "issues" 'such as incorrect warp density prior to weaving a large piece of fabric

Step 3 is best accomplished with a contrasting test weft to flush out any crossed threads or threading errors. It can be thicker than planned for this - but for threading density, use weft of the planned weight.

And YES, I have resleyed many a warp in both directions because the fabric on the loom wasn't the way I'd envisioned it - I always plan the width so that squeezing the warp together a little still results in a fabric that is wide enough for the anticipated usage.

ingamarie

Why /how do you open a shed when your beaming B2F.. I haven't even threaded my heddles at that point....

claudia (not verified)

You're right, I didn't think that one through carefully.  It's f2b when you open the shed. 

Thanks for the correction.

Claudia

needles4ewe (not verified)

I'd like a copy of that list when you get back.

thanks!

Linda

ingamarie

that makes more sense.  I've only warped f2b twice in my life-- why would you open the shed When beaming. It seems like that would put even more stress on your warp. 

I guess that points out a complexity in having a list. Everyone warps differently and one person's must is another persons must not. Suggestions are always good though!

marie

Submitted by Anonymous (not verified) on