I'm weaving the full 110 cm (43") on my GlimĂ„kra, and I have to give the shuttles a real push to get them to go all the way across. When I do that the weft spins of the bobbin and ends up getting tangled on the pin in the shuttle. I usually use paper quills and swedish shuttles, but they're too light to make it all the way across, so I switched to old LeClerc shuttles with their plastic bobbins. I'm not as used to winding those bobbins.. or maybe there's another problem. Any one have a pearl of wisdom for me there??  marie

Comments

Karren K. Brito

Try and end feed shuttle.  I have a 48" AVL and I can easily weave full width with the AVL end feed hand shuttle.

tommye scanlin

 Try a rubber washer sort of thing  to take up space at each end of the plastic bobbin, keeping the bobbin from being pushed too far to one side or the other in the opening of the LeClerc shuttle.  You can take the shuttle and a bobbin in to a hardware store and try out the best size to use (hardware stores are great places to find make-shift weaving tools!).

Tommye

weaver-dyer (not verified)

If there is room, place a sewing machine bobbin or a bead or two on each end of the pin. 

debmcclintock

following up on Tommye's idea, maybe look at fishing bead weights.....they can place your pirn where it needs to be AND add additional weight to the shuttle.  If you can find the weights that are bead shaped with the hole in the middle.  

This is where you earn your reputation at your local fishing or hardware store when you walk in with a piece of weaving equipment and the sales folks try to figure out what you need and they run next time they see you with equipment in hand! 

Michael White

Hi, when winding your plastic bobbins make then fuller in the middle and taper both ends. If you fill the bobbin too full they will run off on the ends.

Michael

ingamarie

Thanks everyone. Jonas (my son--12) and I already have quite a rep. at the local hardware store, we'll confuse them further byb bringing in shuttle.  looking for an o ring or washer.. I"ll try winding the plastic bobbin more like I do a quill too, and not go to the ends. That might help.  l'd like to get the shuttles I have to work before going out to get new ones. It's occurred to me that putting an o-ring on the pin might make it possible to use my trusty and preferred paper quills and skip the plastic altogether!  marie

weaversouth (not verified)

I would second the recommendation for end-feeds!  They handle so smoothly and consistently.

Nancy C

Joanne Hall

Hi Marie,

I would try the shuttles you ordinarily use.  The problem with the Leclerc shuttle and using quills is that their metal spindle has a flattened end, probably to keep the plastic bobbin from jamming into the end of the shuttle.  That flat part of the spindle stops the quills from turning.

And putting beads or other things on each side of the plastic bobbin will increase the drag on the yarn, because the bobbin can then not go back and forth to release the weft.  So, it will not pull out so freely from the shuttle.  And it may pull in the selvages.

So, I would try two things.

Practice a little with the Leclerc shuttle and make sure you are not throwing it too hard or too fast.

Then, go back to your ordinary shuttles, wind the quills tightly and give it a try.  You might just need to throw it a little faster than you did when you tried it the first time.

Joanne

Sara von Tresckow

Like Joanne, I find the Folke Samuelsson shuttles superb. Skip the plastic bobbins on any shuttle - they rattle around and let too much yarn off. My personal favorite package is the cardboard tube after it has been used a while and it slightly out of round.

I originally got the Samuelsson shuttles for the drawloom, but now use them on all my looms. The weights keep the shuttle level so it glides over the weft like no other that I use.

Submitted by ingamarie on