HI All.....I recently had a painted warp on my loom and was working on the last piece when I realized I would not be able to forward the warp enough to get the length I needed out of the last piece. I debated and thought about what to do about the problem and came up with a solution. I had posted my query on WeaveTech and got some good advice and thought you all might find yourselves in a similar situation, so I decided to post my problem and solution here.
I put some photos of my warp extension experience on my website if anyone wants to see. Unfortunately, I forgot to take a photo of the lease sticks in the warp and in the extension warp so I could tie the knots.......if you want to see how I managed to eke out and extra 10" of weaving from my painted warp, go to www.subudesigns.com When you arrive, click on Gallery, then in the drop down box choose "extending a warp" (it is at the bottom). Then click on each individual photo to get a closer view.
Here is what I did to solve my problem:
1. Had to figure a way to extend the warp so I could weave up to 10" of the
loom waste.
a. Warp was fixed to a rod which was slipped into the tabs of the warp
beam apron. This meant
the warp would only extend to the rearmost shafts, and I needed more.
b. Determined I had to extend the length of the warp so I could get the
full weaving length.
2. Determined the warp had to be extended thread by thread.
a. Threads had to go thru heddles.
b. Wove the warp until the apron rod came up over the back beam
3. First step was to wind a warp of the extension threads. I wound a one
yard warp (originally I did 30" but before cutting determined it was not
enough). I kept a thread by thread cross in this warp and kept the other
end uncut. I tied off the cross and transferred this warp to lease sticks
secured to the back beam of the loom.
4. Before cutting the warp, I treadled the tabby sheds and inserted dowels
into the tabby sheds behind the shafts. I tied them securely in place so
they would not move and would not jeopardize my threading. Once the dowels
were fully secured, I cut the warp from the apron rod one bout at a time. I
tied that bout in a slip knot so as not to lose my threading order.
5. With lease sticks and dowels secure, and my threading order for the warp
and the extensions in good order, I started at the left and tied each
extension to each warp thread in order. This operation took less than an
hour, as I had 180 threads. I was going to tie weavers knots (and did in
several threads) but quickly realized that they were taking up more of the
warp that I cared to lose, so switched to overhand knots. These are secure
and easy to tie. I took the advice to keep the tails very short and most
did not exceed 1/4".
6. When all knots were tied, I separated the warp into four sections and
made sure the weight would be evenly distributed on each thread by combing
out the extensions and tying a slip knot at the end. Then I weighted each
section with a large S hook and several large washers. Total weight on the
warp was about 15 lbs. When I attempted to weave, I discovered this was not
enough weight.
7. Having to add weight, I decided to use water jugs. I combined two
sections that I had previously weighted and tied a slip knot in each. Then
I used a large S hook to attach a full gallon milk jug full of water to each
section. This was precisely the amount of weight needed for me to continue
weaving.
8. Weaving went exceptionally smoothly. As the knots began to enter the
heddles, there was little resistance and no shedding problems. For the last
6" of weaving, the knots had been forwarded to enter in all shafts numbered
6-14. Most sheds were quite clean, with the exception of the very last inch
when the tabby shed created by lifting shafts 3-24 was a little sticky. A
quick strum of the warp cleared that away and the weaving was finished
without incident.
Hope this helps if anyone finds themselves in the predicament that I was in.......the pieces are now off the loom and wet finished and I am very, very pleased with the results!
Su :-)
Comments