claudia (not verified)

There was another thread in the Forums about 2 weeks ago with the same concern.  Try searching Forums and it should appear.  I know there were lots of suggestions for removing rust.

If you want a passenger next time you go riding around the PA countryside, let me know.  Sounds like fun but I don't drive any more and love to go for car trips.

Claudia

Bagoyarn (not verified)

 I recently had two very rusted reeds from two used looms and used everything everyone suggested, the only thing that worked for me was a product called Krud Kutter "The Must for Rust", it comes in a spray bottle and following the directions 30 min later  all the rust was gone. I purchased it at  Home Depot. After the rust was removed I put gun oil on a rag and wiped it on the reed.. I used the Krud Kutter for the heddles too.

Hope this helps..

rosearbor (not verified)

 I think the name you are looking for is "naval jelly".  By all accounts I've heard it works very well, but must be rinsed off well.

retrothreads (not verified)

I have a Macomber exactly like yours and would love some help tying up the pedals (treadles ?). I am in DC also. Can I contact you by email ? Mine is [email protected]

Really appreciate any advice on this loom !

Thanks, Carol

anatcheva (not verified)

Sure. I no longer have the Macomber but it is a loom I know quite well (a result of taking it apart and putting it back together again). I'll send you an email.

sequel (not verified)

The first step in restoring the finish is to find out what finish was on it in the first place! 

Modern looms, like Macomber and Hammett often have a sprayed on lacquer, Schacht uses Watco penetrating oil.  Homebuilt looms might have just about anything!  Consult a good book on refinishing antiques for how to determine the old finish.  Usually it's a matter of applying whatever was the vehicle for the product and see if it softens the finish - lacquer thinner for lacquer, mineral spirits for varnish, denatured alcohol for shellac, and so on.  Of course you'd try it on a spot where it wouldn't show...

As for applying boiled linseed oil - I did an antique loom at an historic site that was to be stored and used in the damp basement of the house.  My husband (forestry type) told me that linseed oil is a perfect breeding ground for mold and mold is what I had cleaned off the loom to begin with! 

NanciElaine (not verified)

I had good luck removing rust from 2 reeds that came with the little 4 harness, 4 treadle Lillstina loom I found on Craigslist, by soaking old hand towels in vinegar, placing them under and over the reeds, put it all in a big plastic trash bag for 24 hours - am doing the 10 dent reed one more time as I missed some areas but it worked like magic.  Wiped the reeds with the vinegary rags then used an old toothbrush under running water and a final pass with very fine steel wool. If you do this, don't expect the rust stains to come out of the towels.   I didn't know what to put on the reeds afterwards.  Put the finished 5 dent in front of a fan for an hour or so to thorougly dry.  Will look for some gun oil - would sewing machine oil, lightly wiped on, then off work?  Still trying to find out more about Lillstina looms if anyone knows anything.  Mine is not collapsible - is 31" with a 28" weaving width - the legs are fixed.  Wonderful, sturdy, cute as a bug in a rug, loom.  I'm going to take the harnesses out and dunk in soapy water then rinse, to clean the string heddles.  They're in great shape, but dusty and dirty.

Alaire Rieffel (not verified)

 Thanks!  Vinegar sounds lots better than using some of those scarey chemicals!  

I've started cleaning the first of my 3 looms with Murphy Oil soap and fine steel wool--under all the crud is beautiful maple (?).

 If it is of interest, there was a thread on Weavetech today about the best kind of tape to use for reeds--gaffers cloth tape--from professional photo store or online...

 

NanciElaine (not verified)

Thanks!  I'll look into it.

Slipstream (not verified)

This is a bit late after the rest of the posts but just in case someone is looking for information my favorite means of destroying wood pests including termites, powder post beetles, and fungi is with heat.  I restore toehr antiques and I have a set up with stove pipe wrapped with house insulation and a damper on the end of the stove pipe.  I use a heat gun like the type you use to remove paint (Home Depot, Ryobi 1200 deg) and I use a meat thermometer stuck in the stove pipe through a drilled hole.  Raise the temperature to 140 deg F for 45 minutes (minimum for a 2 X 4 more for larger cross-section wood) and it kills all the pests.  I like to inlet a new piece of wood into the rotten part if possible if not then the various dry rot cures work well.

 

Best regards,

Charles