I'm waiting for my 8 shaft Baby Wolf to arrive. Can everyone say Whooooopppppppppeeeeeeeeeeeeee? To stop obsessing about the arrival, I've been gathering information & drafts, I'm still obessing, just in a functional way. LOL!

What is the maximum number of shafts you should tie to one treadle? Specifically, I'm looking at an 8 shaft double weave window tie-up.The double weave tie-up on 4 shafts was easy peasy for me to understand - all the tie-ups were next to each other. For some reason, my brain freezes when it comes to doing the 8 shaft tie up. I just can't envision how to tie-up shafts not next to each other. Or.... am I missing something? I feel like I have a huge hole in my knowledge base now. Will I have to tie-up so that I use 3 treadles at once, or do I need more than 10 treadles to avoid that?

Also, for those who own Baby Wolf's, what are the beater pegs for on each end of the beater?

 

TIA!

Comments

laurafry

7?  

How many shafts you tie to a treadle will depend on the weave structure.  e.g. with Bronson Lace one plain weave shed is shaft 1, the other is 2, 3, 4, 5, 6, 7, 8

For Summer and Winter, one plain weave shed is 1,2 with the other being 3,4,5,6,7,8.  and so on.

cheers,

Laura

kerstinfroberg

On my website, there are  couple of articles about the construction of double layer weaves - maybe this can be of help?

pammersw

I've been using a rented Baby Wolf for about 4 months now, and I have no idea what the pegs on the end of the beater are for! They don't touch anything on the forward most or rear most swings, my first guess. Maybe someone else knows.

ReedGuy

Pammersw, are they up top of the uprights? If so, they adjust the beater height.

The reason I have two, is I take that free one above and put it below the bar there when removing the beater, so the bar does not slip down and collide with the hand rail by the reed when I let go of it.

katiemac

Thanks everyone! I think I need to just warp & try some tie-ups for the 8 shaft double weave windows & figure it out that way. I need to re-read the info from my double weave book, too.

ReedGuy, the beater pegs are attached to the side of the beater upright & extend beyond the side of the loom a bit. They're just below the slot that holds the top beater bar. There's already a peg to hold the beater upright, so it's not for that.

I'll email Schacht & see what they have to say.

katiemac

Ohhhhhhhhhhhhh!!! I just figured it out. I was looking at the labeled picture at the Schacht site & saw it. Having never had an 8 shaft floor loom, I didn't realise how the shafts physically attach to treadles, even multiple treadles at once!!!! I feel a little silly now. LOL!

mneligh

When the BW is folded the pegs on the sides of the beater prevent the beater from falling through the front beam onto the floor.  They don't do anything when you're weaving.

If you thread BTF (I don't think the BW was designed like this or why would the back beam lift off?) or rethread the loom between pieces, you can use them to tie tje beater in place so you can get to the heddles more easily.

That is, if I understand the pegs in question . . . If not, send a photo indicating the pegs.

pammersw

The back beam doesn't lift off on the Baby Wolf I have, it's fastened with screws. I always warp back to front on it! :)

The height adjustment for the reed is far lower. I think the pegs probably are for when it is folded. Thanks!

ReedGuy

Then, your top is a fixed point and you adjust height down by the beater with a bolt or something threaded?

Every loom is a little different :)

sequel (not verified)

Yep, everyone got it right.  The side pegs are to keep the beater from falling out when you fold and unfold the loom.  This was a serious problem with the early Kessenich loom.  The beater stayed put when your folded and unfolded the loom with a warp on, but take the warp off and you better watch your toes!  Lots of these Kessenich looms have glued places on the upper beater part (handtree?) where they hit the deck!

 

Also remember the metal bars sticking out the back on your Baby Wolf.  They go into the castle and out again when you fold and unfold the loom.  Only I never remember which way is which to keep the black knob in place...

katiemac

Thanks everyone! I hadn't read all the replies here yet, when I emailed Schacht. Yep, the pegs are to keep the beater from falling out of the front of the loom when folded. It's being delivered tomorrow! 8-))

pammersw

ReedGuy - re "

Then, your top is a fixed point and you adjust height down by the beater with a bolt or something threaded?"

 

The whole wood frame that holds the reed is on wood supports at each side. At the bottom of those wood supports,  they attach to a metal piece. The location of that attachment to the metal piece is adjustable, resulting in raising or lowering the whole beater assembly. If I can get the photo to post...those are the metal things attached halfway up the front legs.

 

 

ReedGuy

Ah yes, I see. I keep thinking Swedish looms all the time for some reason. A flaw of mine.  ;)

pammersw

BTW, that is an 8 shaft loom very similar to the one just purchased by the original poster. It is a 36" Mighty Wolf rather than the 26" Baby Wolf because the photo was clearer - but they are the same except for width.

Lavonne

Hello

Just another newbie :) I just received my Baby (wolf) and have been working on a project, until I realized in using only 4 shafts the other 8 are in the way. I removed the 8th shaft and noticed their is a metal piece that the shaft sats on that sticks up once its removed. I can't leave the 4 on because the 20 inches I need for weaving are touching the unused heddles on the  last 4 shafts. What should I do. is there a way to anchor the shaft supports down. Do i just ignore them because they will not touch the warp threads when set up is complete.

Thanks all

PS Took a classes put only wove narrow pieces :)..

Submitted by katiemac on